How to fix a Troy-Bilt TB525 EC that will not idle?
If your Troy-Bilt Trimmer won't idle, there are a few potential causes. The air filter may be plugged, so replace or clean it. Old fuel (over 30 days) can also cause idling issues, so drain the fuel tank and add fresh fuel. Finally, the idle speed may be improperly set; adjust it according to the Idle Speed Adjustment section.
What to do if my Troy-Bilt Trimmer engine lacks power or stalls?
If your Troy-Bilt Trimmer engine lacks power or stalls, consider these possible causes. Old fuel (over 30 days) can be a culprit, so drain the fuel tank and add fresh fuel. A fouled spark plug can also cause these issues, so replace or clean the spark plug. If the outside temperature is above 90°F, move the choke lever to Position 2, press the primer bulb 10 times, squeeze the throttle control and pull the starter rope until the unit starts. Run the unit for 2-5 minutes, then move the choke lever to Position 3.
Why is the cutting attachment on my Troy-Bilt Trimmer not advancing line?
If the cutting attachment on your Troy-Bilt Trimmer isn't advancing line, several issues could be the cause. These include: * Cutting attachment bound with grass: Stop the engine and clean cutting attachment. * Cutting attachment out of line: Refill with new line. * Inner reel bound up: Replace the inner reel. * Cutting head dirty: Clean inner reel and outer spool. * Line welded: Disassemble, remove the welded section and rewind. * Line twisted when refilled: Disassemble and rewind the line. * Not enough line is exposed: Push the bump head and pull out line until 4 inches (102 mm) of line is outside of the cutting attachment. * Oil, cleaner or lubricant in cutting head: Clean and thoroughly dry the cutting head.
Why won't my Troy-Bilt TB525 EC Trimmer engine accelerate?
If your Troy-Bilt Trimmer engine won't accelerate, it might be due to several reasons. Old fuel (over 30 days) can cause this issue, so try draining the fuel tank and adding fresh fuel. Another possibility is that the cutting attachment is bound with grass; in this case, stop the engine and clean the cutting attachment. A dirty air filter can also prevent acceleration, so clean or replace the air filter.
Why is my Troy-Bilt TB525 EC a potential fire hazard?
To prevent your Troy-Bilt Trimmer from becoming a fire hazard, never store it with fuel in the tank, as fuel fumes may reach an open flame or spark.
How to prevent injury when cleaning Troy-Bilt TB525 EC?
To prevent injury when cleaning or servicing your Troy-Bilt Trimmer, always turn the unit off and allow it to cool first.
What to do if I didn't drain gasoline from Troy-Bilt Trimmer before storage?
To address the issue of not completely draining gasoline from the carburetor of your Troy-Bilt Trimmer before storage, start the engine and allow it to run until it stalls.
What to do if oil left in cylinder of Troy-Bilt TB525 EC after storage?
If oil left in the cylinder is causing starting issues with your Troy-Bilt Trimmer after storage, remove the spark plug and drain all of the oil from the cylinder before attempting to start it.
How to prevent damage to plastic housing of Troy-Bilt TB525 EC?
To prevent damage to the plastic housing or handle of your Troy-Bilt Trimmer, do not use strong detergents or household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene.
Key safety rules for operating the unit.
Specific safety precautions for gasoline-powered units.
Safety guidelines to follow during operation.
Details on correct oil and fuel usage, including warnings.
Step-by-step guide to start the engine.
Steps to safely stop the engine.
General| Engine Type | 2-cycle |
|---|---|
| Line Diameter | 0.095 inches |
| Line Feed | Bump Head |
| Shaft Type | Straight |
| Attachment Capable | Yes |
| Cutting Width | 18 inches |
| Start System | Spring Assist |
To Next Page