Truma Mover smart A - User Manual

Questions and Answers

M
Michael YangJul 28, 2025
What to do if Truma Mover smart A Automobile Accessories mover is not responding to the remote control?
- T
  Tammy MullenJul 28, 2025
  If your Truma Automobile Accessories mover isn't responding to the remote control, or is responding intermittently, it could be due to a low battery. First, check the battery and battery contacts of the remote control. If needed, replace the battery or clean the battery contacts. Another cause could be a low battery in the mover itself, indicated by a flashing green LED on the control unit. In this case, check, charge, or replace the mover's battery.
N
Nathan WalkerAug 3, 2025
What to do if Truma Mover smart A Automobile Accessories mover does not engage on one side?
- C
  Carl HansenAug 3, 2025
  If the Truma Automobile Accessories mover does not engage on one side (only Mover smart A), ensure that when disengaging the mover, the power supply isn't interrupted, and the remote control isn't switched off. The process is complete only after the indicator on the remote control stops flashing. You can also manually engage the Mover with the socket wrench by approximately two clockwise resolutions, then try engaging the Mover once again.
M
Melinda SmithAug 9, 2025
Why is my Truma Automobile Accessories mover not working?
- M
  Michael SheltonAug 9, 2025
  If your Truma Automobile Accessories mover isn't working, begin by checking the power supply; the green LED on the control unit should be lit. If it’s still not working, the fuse in the mover’s battery connector cable may be faulty and should be replaced with an original Truma spare part. As an additional step, you can interrupt the power supply for at least 20 seconds and then re-establish it to see if the green LED on the control unit illuminates.
C
Charles BrockAug 15, 2025
What to do if the red LED on the Truma Mover smart A Automobile Accessories mover control unit is flashing?
- A
  Anna MitchellAug 15, 2025
  If the red LED on the control unit of your Truma Automobile Accessories mover is flashing, it indicates that the control unit has overheated. To resolve this, interrupt the power supply using the battery cut-off switch and remove the key. Allow the control unit to cool down for at least 20 minutes before restarting the mover.
W
williamschristopherAug 21, 2025
What to do if Truma Mover smart A Automobile Accessories drive roller slides down on the wheel?
- E
  Eric FrazierAug 21, 2025
  If the drive roller on your Truma Automobile Accessories is sliding down on the wheel, first check the tire pressure and adjust it if necessary. Also, inspect the tire profile and replace the tires if needed. As a final step, disengage the mover and measure the distance between the tires and drive roller, ensuring it is 20 mm.

Summary

Safety Instructions

General Safety Precautions

Essential safety guidelines to follow before and during operation. Covers user responsibility and general warnings.

Power Supply

Batteries and Charger

Operating Instructions

Setting Up the Mover

Step-by-step guide for initial setup, including power supply and engaging the mover.

Remote Control and Manoeuvring

Manoeuvring the Caravan

Detailed instructions on how to move the caravan using the remote control, including safety notes.

Disengaging and Maintenance

Disengaging the Mover

Steps for disengaging Mover smart A (automatic) and Mover smart M (manual).

Inspections and Troubleshooting

Troubleshooting Guide

Lists common faults, their causes, and recommended remedies for the mover.

Technical Information and Compliance

Tuning Control Unit to Remote

Procedure to tune the electronic control unit to the radio remote control for initial setup.

Manufacturers Warranty Declaration

Warranty Scope and Duration

Warranty Exclusions

Making a Warranty Claim

Truma Mover smart A Specifications

General

Suitable for	Single-axle caravans
Permissible total weight	2000 kg
Power supply	12 V DC
Remote control	Yes
Automatic engagement	Yes
Maximum gradient	13%
Protection Class	IP54