EasyManua.ls Logo

Truper SME-10 - User Manual

Truper SME-10
32 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Instructivo de
Sierra de mesa
SME-10
Modelo Código
SME-10
Este instructivo es para:
16143
2,2 Hp
Potencia
1 650 W
ATENCIÓN
Lea este Instructivo por completo
antes de usar la herramienta.
ESPAÑOL
ENGLISH

Table of Contents

Questions and Answers

  • J
    John HarrisAug 13, 2025
    Why does my Truper Saw not start?
    • M
      Martha HernandezAug 13, 2025
      If your Truper Saw isn't starting, there could be several reasons. Try the following: * Connect the cable to the power supply. * Replace the fuse or enable the overload protection switch. * Replace the cable. * Replace the extension cable or wiring with the correct gauge. * Reduce the feeding speed. * Clean or replace the disc. * Check and adjust the sawing guide alignment. * Use a piece of wood that isn't warped. * Call your utilities company. * Adjust the miter guide or sawing guide and tighten the knobs. * Adjust the cutting disc to 90° in the table using a set square and set the pointer to zero.
  • A
    Alison MendozaAug 17, 2025
    Why does the Truper Saw vibrate in excess?
    • P
      Pedro MezaAug 17, 2025
      Excessive vibration in your Truper Saw can be caused by: * The equipment being set on uneven ground. To fix this, set the equipment on flat and leveled ground. * A damaged disc. If the disc is damaged, replace it.
  • T
    Timothy RichardsonAug 21, 2025
    What to do if material gets stuck in the disc of my Truper Saw?
    • J
      Julie MorrisonAug 21, 2025
      If material gets stuck in the disc of your Truper Saw, it might be because: * The sawing guide is misaligned. Check and adjust the sawing guide. * The disc is stuck because the wood is warped. Use a piece of wood that isn't warped.
  • J
    Joseph WebbAug 25, 2025
    How to prevent material from being sent back by the Truper Saw disc?
    • M
      Mark RobertsAug 25, 2025
      To prevent material from being sent back with the disc movement on your Truper Saw, consider the following: * Adjust the sawing guide angle if it's misaligned. * Adjust the spacer angle if it's misaligned. * Support the material in the sawing guide if it's being fed without it. * Set the spacer if it's not installed. * Replace the disc if it's dull or worn. * Support and push the material with the pushers and pushing block until they pass through the disc if the material gets loose before going through the disc. * Tighten the miter guide knob if it's loose.
  • S
    Samantha JacksonAug 28, 2025
    Why are the cuts not satisfactory with my Truper Saw?
    • C
      Charles MendezAug 28, 2025
      If the cuts from your Truper Saw aren't satisfactory, try these solutions: * Check and adjust the spacer alignment. * Replace the disc. * Change the disc position. * Remove the disc and clean it with turpentine and steel mesh. * Replace the disc. * Clean the table with turpentine and steel mesh.
  • C
    Christopher WallsSep 1, 2025
    Why is the Truper Saw disc not reaching maximum speed?
    • A
      Adam HaasSep 1, 2025
      The disc might not be reaching maximum speed because: * The disc is dull or damaged. * The disc is mounted backwards. * The disc has pitch or resin. * The disc is not adequate for that job. * The table has pit or resin hindering the operation. * Replace the extension cable or wiring with the right gauge. * Call your utilities company.
  • V
    Vernon SimmonsSep 5, 2025
    How to fix the disc not raising or tilting freely on my Truper Saw?
    • A
      Angela NashSep 5, 2025
      If the disc on your Truper Saw isn't raising or tilting freely, it's likely because the control mechanisms are dirty. Brush out or blow away all the residues accumulated in the control mechanisms.
  • M
    masoncolleenSep 9, 2025
    Why is the material stuck in the spacer of my Truper Saw?
    • W
      William KerrSep 9, 2025
      The material may be stuck in the spacer because the spacer is misaligned.

Summary

Technical Specifications

Power Requirements

General Safety Warnings

Power Saw Safety Warnings

Before Operating the Saw

Essential checks and preparations before starting the saw.

While Operating the Saw

Safe practices during saw operation, hand positioning, and material handling.

Kickback Prevention

How to prevent and handle kickback incidents.

Additional Safety Measures

Saw Mounting Procedure

Spacer and Disc Guard Assembly

Instructions for installing the spacer and disc guard assembly.

Sawing Guide Assembly and Alignment

Steps for assembling and aligning the sawing guide.

Table Saw Adjustments

Disc Height Adjustment

Cutting Angle Adjustment

Calibrate Disc Angle

Calibrate with Work Table Surface

Aligning the disc angle with the table surface.

Calibrate with Miter Guide Slots

Aligning the disc angle with the miter guide slots.

Starting Up the Table Saw

Turning ON and OFF

Procedures for safely powering the saw on and off.

Table Saw Operation

Cutting Through the Wood Grain

Techniques for making cuts parallel to the wood grain.

Cutting Operations

Cutting Along the Wood Grain

How to make cuts parallel to the wood grain safely.

Cutting Small Pieces

Safety measures and tools for cutting small work pieces.

Table Saw Maintenance

Cutting Disc Replacement

Steps for safely replacing the cutting disc.

Carbon Brush Replacement

Troubleshooting Common Problems

Saw Does Not Start

Overload Protection Activated Often

Cutting Angles Not Precise

Material Stuck in Disc or Spacer

Unsatisfactory Cuts

Disc Not Reaching Maximum Speed

Excessive Equipment Vibration

Disc Movement Issues

Material Ejected Backwards

Preventing material from being ejected backwards.

Truper SME-10 Specifications

General IconGeneral
BrandTruper
ModelSME-10
CategorySaw
LanguageEnglish

Related product manuals