Tyco WS4933 User Manual

The WS4933 is designed to monitor the CO gas level in residential dwellings and give
early warning before dangerous levels are detected. This device is intended to be used
with a compatible wireless alarm system. The detector consists of an electrochemical
carbon monoxide sensor assembly coupled to a wireless transmitter.
The Wireless Carbon Monoxide Alarm communicates with the control panel and can
send alarm, tamper and battery condition messages to the system receiver.
Caution: The detector expiry date is stamped on the detector. After the expiry date,
the detector should not be used - do not wait for end-of-life indication!
CAUTION: Unauthorized removal of the unit from the mounting bracket will
initiate a tamper alert.
Warnings
The WS4933 wireless Carbon Monoxide detector shall be installed and used within an
environment that provides the pollution degree max 2 and overvoltages category II in
indoor, non hazardous locations only. The equipment is designed to be installed by
skilled persons only (skilled person is defined as a person with relevant education or
experience to enable him or her to identify hazards and to take appropriate actions to
reduce the risks of injury to themselves and others).
Failure to properly install, test and maintain a CO detector may cause it to fail, res-
ulting in loss of life. Installation of the CO detector should not be used as a substitute
for proper installation, use and maintenance of fuel burning appliances, including
appropriate ventilation and exhaust systems.
This carbon monoxide detector is designed for indoor use only. Do not expose it to
rain or moisture. Do not knock or drop the detector. Do not open or tamper with the
detector as this could cause malfunction. The detector will not protect against the risk
of carbon monoxide poisoning if not properly installed.
CAUTION: This device will only indicate the presence of carbon monoxide gas
at the sensor. Carbon monoxide gas may be present in other areas. This carbon
monoxide alarming device is designed to detect carbon monoxide gas from any
source of combustion. It is not designed to detect smoke, fire or other gases
unless the product has been investigated and determined to comply with applic-
able requirements.
Figure 1: Wireless CO Detector
C
D
A
B
Legend
A. Alarm LED (see Table 1 for LED indications)
B. Tamper release opening
C. Test/Hush button
D. Battery compartment
E. Breakaway tab (see Figure 3)
WS4933 (433MHz) Wireless Carbon Monoxide Detector
Installation and Operating Instructions
Read these instructions thoroughly before installation and use of the WS4933.

Tyco WS4933 Specifications

General

Brand	Tyco
Model	WS4933
Category	Security Sensors
Language	English

Summary

Installation and Operating Instructions

Warnings

Essential safety warnings for installation and use of the CO detector.

Detector Features

Identifies key components like LED, buttons, battery compartment, and tamper release.

Battery Installation

Step-by-step guide for replacing the detector's battery.

Enrollment Process

How to register the detector's serial number with the control panel.

Selecting a Location

Guidance on choosing the optimal placement for effective CO detection.

Prohibited Installation Locations

Critical locations to avoid for CO detector installation to ensure proper function.

Mounting Instructions

Instructions for physically attaching the detector to a wall or ceiling.

Audible and Visual Indicators

Describes LED and sounder signals for different detector statuses and events.

Tamper Protection Feature

Details the tamper-resistant feature and how to operate it.

Testing the CO Detector

Procedures for testing the detector's functionality and alarm.

Routine Maintenance

Routine checks and cleaning to ensure proper detector function and longevity.

Specifications and CO Information

Understanding Carbon Monoxide

Explains the nature, sources, and dangers of carbon monoxide gas.

Carbon Monoxide Poisoning Symptoms

Lists symptoms associated with CO poisoning at various exposure levels.

Alarm Response and Safety Precautions

Action During Alarm

Immediate steps to take when the CO alarm is activated.

Post-Alarm Procedures

Steps to verify detector function after a CO event is resolved.

Key Warnings and Limitations

Important restrictions and warnings regarding the detector's intended use and capabilities.

Product Considerations and Legal

Transient CO Conditions

Lists environmental and appliance factors that can cause temporary CO situations.

Handling and Care Precautions

Warnings about lithium battery handling and not painting the unit.

Limited Warranty Information

Outlines the warranty period and terms for the product.

End-User License Agreement (EULA)

Terms and conditions for using the associated software and hardware.

Software Licensing Terms

Software Grant of License

Details the rights granted for installing and using the software product.

Software Usage Limitations

Outlines restrictions on reverse engineering, decompilation, and component separation.

Software Warranty Disclaimer

States the software is provided "as is" with no warranties.

Regulatory and Compliance Statements

FCC Compliance Statement

Information regarding FCC rules and potential radio frequency interference.

Industry Canada Compliance

Statement regarding compliance with Industry Canada's RSS standards.