U-Line H-7176 User Manual

PAGE 1 OF 12 0521 IH-2932
DIGITAL
KEY CABINET
1-800-295-5510
uline.com
H-2932, H-4734, H-6265
H-7176, H-7766
FEATURE KNOB
KEYPAD
BUTTONS
PROGRAM
BUTTON
GREEN AND
RED LEDS
YELLOW
LED
FUNCTION
Moves lock mechanism
90 or 180 degrees
clockwise or
counterclockwise
to lock and unlock
cabinet.
For entering and
programming lock
codes.
Initiate programming
mode by pressing the
front thin edge of the
black button.
Will flash and
illuminate to indicate
operating conditions.
Will flash five times
after lock is operated
to signify the battery
level is low and should
be replaced.
OVERVIEW OF CONTROLS
INSTRUCTIONS
This lock can operate using 3 codes (factory or master
code, supervisor code and user code).
Factory/Master Code – This code must
be reprogrammed to a 6-digit master
code. (See Page 2)
Supervisor/User Codes – 3 to 6 digits
need to be programmed into
the lock by following the steps. All
codes are retained by the lock after
unlocking and if the battery is changed.
A Note on Codes – The numbers 6, 7, 8 and 9 can be
entered by pressing two keys simultaneously in order to
produce a sum.
For example, 2 and 4 can be pressed simultaneously to
produce the number 6.
NOTE: If the code was programmed using
2 + 4 as the 6 digit, the 2 + 4 must be used
when accessing the lock. Other combinations
that equal six, such as 1 + 5, are distinguished
from 2 + 4.
5
5
5
6
5
5
50
5
49
2
5
28
5
27
3
4
5
2
1
ELECTRONIC LOCK
ELECTRONIC LOCK FEATURES
# DESCRIPTION
1 Knob
2 Keypad
3 Battery Holder With Cover
4 Program Button
5 Yellow LED – Low Battery
6 Red LED – Error
7 Green LED – Proceed
1 3
4
5 6 7
2
ELECTRONIC LOCK FUNCTIONS
Factory/Master
Code
Supervisor Code
3-6 Digits
User Code
3-6 Digits
Para Español, vea páginas 5-8.
Pour le français, consulter les pages 9-12.

U-Line H-7176 Specifications

General

Brand	U-Line
Model	H-7176
Category	Home Safety Product
Language	English

Summary

Overview of Electronic Lock Controls

Electronic Lock Features

Lists components like Knob, Keypad, Battery Holder, Program Button, and LEDs with their functions.

Electronic Lock Functions

Details the operation of Knob, Keypad, Program Button, and LEDs for lock functions.

Lock Cabinet Instructions

Code Management: Factory/Master Code

Reprogrammable 6-digit master code is crucial for initial setup and operation.

Code Management: Supervisor/User Codes

3-6 digit codes for users and supervisors, persistent across battery changes.

Code Entry Note

Explains simultaneous key presses for specific digits and code uniqueness.

Programming Procedures

Programming a 6-Digit Master Code

Step-by-step guide to overwrite the factory code with a new 6-digit master code.

Programming a Supervisor Code

Procedure to set or overwrite a 3-6 digit supervisor code using the master code.

Programming a User Code

Steps to program a 3-6 digit user code using the supervisor code.

Erasing a User Code

Instructions to remove a user code using the supervisor code and a specific sequence.

Lock Operation and Battery Replacement

Lock Operation

Information on unlocking with a valid code and indications for incorrect entries.

Re-locking the Cabinet

Procedure to turn the knob to the locked position and confirm lock engagement.

Changing Operation Mode

Guide to switch from single user mode to locker mode using master code and button presses.

Replacing the Battery

Detailed steps for removing and replacing the 3-Volt Lithium CR2032 battery.

Battery Replacement Continued

Securing Battery Holder

Instructions for pushing in the battery holder and tightening the retaining screw.

Finalizing Battery Installation

Steps for closing the battery cover and inserting the knob into the locked position.

Troubleshooting Lock Engagement

Guidance if the unit does not lock after battery insertion, suggesting code entry.