Unipulse F701-P - User Manual

To Next Page

01AUG2020REV.1.07

WEIGHING INDICATOR

F701-P

OPERATION MANUAL

Main Page

Table of Contents7
Outline12
Contents of the Package12
About Connectable Devices12
Appearance Description13
Front Panel13
Rear Panel17
Connection18
Load Cell Connection19
6-Wire Connection19
4-Wire Connection20
Connecting Load Cells in Parallel21
Sensors Cable21
Connection of the Load Cell, Power Input Terminal,Rs-485 and External Input/Output Signal Terminal Blocks22
Connection of the Protective Ground23
Setting Method24
Setting Procedure24
How to Designate a Setting Mode no24
How to Register a Setting Value25
Setting Modes28
Setting Mode 028
Setting Mode 128
Setting Mode 230
Setting Mode 330
Setting Mode 432
Setting Mode 533
Calibration34
Span Calibration34
Span Calibration Procedure35
Preparation before Calibration36
LOCK Release36
Unit Display (Setting Mode 4-5)36
Decimal Place (Setting Mode 4-5)36
Capacity (Setting Mode 4-2)37
Min Scale Division (Setting Mode 4-3)37
Balance Weight Value (Setting Mode 4-1)37
Gravitational Acceleration (Setting Mode 4-6)37
1/4 Scale Division (Setting Mode 4-5)38
Zero Calibration39
Span Calibration (Setting Mode 9-1)41
Function Settings42
Display Update Rate (Setting Mode 4-5)42
Subdisplay Selection (Setting Mode 4-5)42
Digital Low Pass Filter (Setting Mode 2-1)42
Moving Average Filter (Setting Mode 2-2)43
Filter in Stable Condition (Setting Mode 1-5)43
Motion Detection(MD) (Setting Mode 1-5, 2-3)44
Setting of Motion Detection Parameters45
Zero Tracking(ZT) (Setting Mode 2-4, 2-5)45
Digital Zero(DZ)46
Digital Zero Clear46
5-10.DZ Regulation Value (Setting Mode 4-4)46
5-11.Gross Weight Display/Net Weight Display46
5-12.One-Touch Tare Subtraction (TARE)47
5-13.One-Touch Tare Subtraction Reset47
5-14.Digital Tare Subtraction (Preset Tare Weight)47
Preset Tare Weight (Setting Mode 1-5)47
Tare Setting (Setting Mode 1-8)48
5-15.Tare Weight Display (Setting Mode 1-9)48
5-16.Key Invalid (Setting Mode 3-5)48
Weighing Setting and Operations49
Comparison Mode (Setting Mode 1-4 Weighing Function 1)49
Near Zero Comparison49
Upper/Lower Limit Comparison Mode50
Upper/Lower Limit Comparison50
Over/Under Comparison Mode52
Discharging Control Mode54
Discharging Control54
About Accumulation57
Total Comparison Selection/Total Limit/Count Limit57
Accumulation Clear57
System-Related Settings and Operations58
LOCK (Soft)58
Passwaord58
Self-Check58
External Input/Output Signals (Control Connector)59
Connector Pin Assignments59
External Control Equipment Connection60
Equivalent Circuit and Example Connection, When Specify the Sink Type60
Equivalent Circuit and Example Connection, When Specify the Source Type61
External Input Signals62
Gross/Net Switch (G/N) <Edge Input62
Digital Zero (D/Z ON) <Edge Input62
Tare Subtraction (TARE ON) <Edge Input62
Tare Subtraction Reset (TARE OFF) <Edge Input62
Accumulation Clear <Edge Input63
HOLD <Level Input63
JUDGE <Level Input63
External Output Signals63
When Comparison Mode 0 (Upper/Lower Limit Comparison Mode) Is Set63
When Comparison Mode 1 (Over/Under Comparison Mode) Is Set64
When Comparison Mode 2 (Discharging Control Mode) Is Set64
Stable64
Weight Error64
Total Limit64
Interface65
Communication Specifications65
Standards65
Connection66
Two-Wire Type (Point to Point)66
Two-Wire Type (Multi Point)66
RS-485-Related Setting Values67
I/F Setting67
ID/ Slave Address for MODBUS-RTU67
Communication Type67
Communication Type68
UNI-Format Commands69
Setting Value Communication Formats74
UNI-Format (Continuous, Auto)75
Modbus-RTU76
Data Address94
About Data96
10Specifications101
10-1.Specifications101
Analog Section101
Display Section101
Setting Section102
External Signals102
Interface103
General Performance103
Accessories103
10-2.Dimensions104
Mounting on a Panel104
Packing Installation105
10-3.Block Diagram107
11Supplements108
11-1.List of Setting Values108
Setting Mode 0108
Setting Mode 1108
Setting Mode 2109
Setting Mode 3109
Setting Mode 4109
Setting Mode 5110
Setting Mode 9110
11-2.Over Scale/Error Display111
Over Scale Display111
Calibration Error Display111
11-3.Troubleshooting112
Over Scale Display112
Calibration Error Display113
Checksum Error Display115
F-RAM Check Error Display115

Need help?

Do you have a question about the Unipulse F701-P and is the answer not in the manual?

Unipulse F701-P Specifications

General

Brand	Unipulse
Model	F701-P
Category	Accessories
Language	English

Related product manuals

Unipulse F701-P - User Manual

Table of Contents

Unipulse F701-P Specifications

Related product manuals