Universal Laser Systems X2-660

Questions and Answers

A
Ashley RodriguezAug 16, 2025
What to do if raster engraving appears sharp on both ends but fuzzy in the middle on Universal Laser Systems Cutter?
- S
  smithjulieAug 16, 2025
  If you notice that the raster engraving appears sharp on both ends but fuzzy in the middle on your Universal Laser Systems Cutter, it could be due to several reasons: * The laser system might be dirty. Clean all optics, rails, bearings, and belts. * Something might be loose. Check the X-axis bearings, drive gear, idler pulley, belt, and optics. * The system may need tuning. Run the “Tuning” feature in the printer driver. * The X-axis belt and/or drive gear might be worn. Replace the belt and/or drive gear and run the “Tuning” feature. * The laser tube might be faulty. Replace the laser tube.
D
David CastilloAug 28, 2025
Why fine detail is missing when raster engraving on Universal Laser Systems X2-660 Cutter?
- A
  Adrian LopezAug 28, 2025
  If you're missing fine details like serifs or thin lines when raster engraving with your Universal Laser Systems Cutter, it might be due to: * The speed being too fast for the material. Try slowing down the engraving speed. * The laser not responding to low duty-cycle, high-speed engraving. Run the enhancement feature in the printer driver. * The system being out of focus. Refocus. * The system needing tuning. Run the “Tuning” feature in the printer driver. * The laser spot size being too big. Use a shorter focal length lens.
T
Timothy FordSep 1, 2025
Why vertical or diagonal background pattern appears when raster engraving on Universal Laser Systems X2-660?
- S
  Sheena WilsonSep 1, 2025
  If you observe a vertical or diagonal background pattern while raster engraving large areas or amounts of material with your Universal Laser Systems Cutter, it could be due to: * A dirty laser system. Clean all optics, rails, bearings and belts. * Loose motion system components. Check the X-axis bearings, belt, and optics. * Worn or damaged X-axis bearings. Replace the X-axis bearings. * Worn or damaged X-axis rail. Replace the X-axis arm.
S
Sandra HollowaySep 4, 2025
Why horizontal background pattern appears when raster engraving on Universal Laser Systems X2-660?
- T
  Travis FieldsSep 4, 2025
  If a horizontal background pattern appears when raster engraving large areas or amounts of material on your Universal Laser Systems Cutter, it could be caused by: * A dirty laser system. Clean all optics, rails, bearings and belts. * The laser being too cold or hot. Ensure the ambient temperature is within specifications. * A faulty laser tube. Replace the laser tube.
K
Kyle EstesSep 7, 2025
Why engraving appears “halftoned” when using colors other than black on Universal Laser Systems X2-660 Cutter?
- Q
  qflemingSep 7, 2025
  If the engraving appears “halftoned” and not solidly filled when using colors other than black on your Universal Laser Systems Cutter, it may be because the graphics, graphic software, graphic software setup, color palette, monitor display colors, or driver settings have changed. Check to see what has changed and refer to the “Computerized Controls” manual to properly set up the graphics software. Also, check the driver settings.
M
Michelle MorrisNov 11, 2025
Why engraving does not appear as deep as it normally does in Universal Laser Systems X2-660 Cutter?
- R
  Ryan MooreNov 12, 2025
  If the engraving does not appear as deep as it normally does on your Universal Laser Systems Cutter, consider the following potential causes and solutions: * A change in graphics, graphic software, graphic software setup, color palette, monitor display colors, or driver settings. Check what has changed and use the Software Setup Guide to properly set up the graphics software and check driver settings. * The system might be out of focus, so refocus it. * The material or its density may have changed, so check the material. * Settings may have been altered, so check power, speed, PPI, and DPI settings. * The laser system might be dirty; clean all optics, rails, bearings, and belts. * Laser tube cooling fan filters might be dirty; check and clean them. * Ambient temperature migh...
J
Joseph ColeNov 19, 2025
Why raster engraving or small text appears like a double image on Universal Laser Systems Cutter?
- N
  nicholas62Nov 19, 2025
  If the raster engraving or small text appears as a double image on your Universal Laser Systems Cutter, consider the following: * The laser system may be dirty. Clean all optics, rails, bearings, and belts. * Changes may have occurred in the graphic, graphic software, graphic software setup, color palette, monitor display colors, or driver settings. Check what has changed and refer to the “Computerized Controls” manual to properly set up the graphics software. Check driver settings. * The speed may be too fast for the material. Slow down the engraving speed. * The system may be out of focus. Refocus. * The system may need tuning. Run the “Tuning” feature in the printer driver. * The X-axis belt and/or drive gear may be worn. Replace the belt and/or drive gear and run the “Tuni...
J
Jason BeckNov 23, 2025
What to do if engraving is sharp on one side and fuzzy on the opposite side on Universal Laser Systems X2-660?
- A
  Angela MendezNov 23, 2025
  If your engraving is sharp, clear, and at a good depth on one side of the table but fuzzy and shallow on the opposite side with your Universal Laser Systems Cutter, here's what you can check: * The system may be out of focus, so refocus. * The laser system may be dirty, so clean all optics, rails, bearings, and belts. * The material may not be level or may vary in thickness. Check the focus point of the material in different places and adjust the height by shimming the material or using more thickness-consistent material. * The table may not be level. Using the focus tool, focus directly on the surface of the table in all four corners. The table should be within +/- .020 inches from one corner to the other. Adjust if necessary. * The laser beam may be out of alignment with the o...