What causes a short-circuit on the heat retention storage tank sensor of a Vaillant Boiler?
A short-circuit on the heat retention storage tank sensor of your Vaillant Boiler can be caused by the sensor plug having a mass short to the casing, a short-circuit in the wiring loom, or a faulty sensor. Contact the service team for assistance.
What to do if the flame goes off during operation and subsequent ignition attempts failed in my Vaillant Boiler?
If the flame goes off during operation and subsequent ignition attempts fail in your Vaillant Boiler, it could be due to the gas supply being temporarily stopped, the ignition transformer having a spark failure, or faulty earthing of the appliance. Contact the service team for assistance.
Why is there a water shortage and a large temperature spread between flow and return probe in my Vaillant Boiler?
A water shortage with a large temperature spread between the flow and return probe in your Vaillant Boiler might be caused by a blocked or defective pump, low pump output, or the flow and return sensors being swapped over. Contact the service team for assistance.
Why is the signal from the water pressure sensor in the wrong range (too low) in my Vaillant Boiler?
If the signal from the water pressure sensor in your Vaillant Boiler is in the wrong range (too low), it may be due to an interrupted line to the water pressure sensor, a short-circuit to 0V, or a faulty water pressure sensor. Contact the service team for assistance.
Why is the signal from the water pressure sensor in the wrong range (too high) in my Vaillant ecoTEC exclusive 832?
If the signal from the water pressure sensor in your Vaillant Boiler is in the wrong range (too high), it could be due to a short-circuit at 5V / 24V in the line to the water pressure sensor or an internal fault in the water pressure sensor. Contact the service team for assistance.
What causes interruption in the return temperature sensor (NTC) of a Vaillant ecoTEC exclusive 832 Boiler?
An interruption in the return temperature sensor (NTC) of your Vaillant Boiler can be caused by a faulty NTC, a faulty NTC cable, a faulty plug connection on the NTC, or a faulty plug connection on the electronics. Contact the service team for assistance.
What does it mean if there is a flow and/or return sensor fault in my Vaillant ecoTEC exclusive 832?
A flow and/or return sensor fault in your Vaillant Boiler indicates that the flow and/or return sensor is faulty, meaning the tolerance is too great. Contact the service team for assistance.
What causes interruption in the feed temperature sensor (NTC) of a Vaillant Boiler?
An interruption in the feed temperature sensor (NTC) of your Vaillant Boiler can be caused by a faulty NTC, a faulty NTC cable, a faulty plug connection on the NTC, or a faulty plug connection on the electronics. Contact the service team for assistance.
What to do if there is a water shortage and the temperature rise is too quick in my Vaillant ecoTEC exclusive 832?
If there is a water shortage and the temperature rise is too quick in your Vaillant Boiler, it may be caused by a blocked pump, low output from the pump, air in the appliance, or the system pressure being too low. Contact the service team for assistance.
What does it mean when the flow/return sensor test is running and heating demands are blocked in my Vaillant Boiler?
If the flow/return sensor test is running and heating demands are blocked in your Vaillant Boiler, the system may display error code S.98.
General safety instructions and regulations to be observed.
Procedures to follow in case of a gas leak.
Procedures to follow in case of flue gas smell.
Detailed instructions and safety warnings for connecting the gas supply.
Instructions for connecting the hot and cold water supply pipes.
Steps for connecting the heating flow and return pipes.
Instructions for fitting the air/flue gas duct and available components.
Instructions for filling the heating system and conditioning the water.
Steps for filling and venting the boiler and the entire heating system.
Procedure for checking and adjusting the CO2 concentration for optimal combustion.
Essential safety precautions before replacing any component.
To Next Page
General