Valcom VIP-801 User Manual

1 947995
ISSUE 6
VIP-801
ENHANCED NETWORK AUDIO PORT
INTRODUCTION
The VIP-801 Enhanced Network Audio Port
enables voice access to a single zone of one-way
paging over an IP network, allowing page zones
to be extended anywhere network connectivity is
available. The VIP-801 can be programmed as a
SIP (Session Initiation Protocol) device for
connectivity to virtually any Voice over IP (VoIP)
telephone system.
SPECIFICATIONS
Features
 1 Audio Output or Input
 2 Form C Relays
 1 Contact Closure Input
 1 SIP identity for registering to a VoIP telephone
system
 RJ-45 jack for network connection
 Front panel activity LED
 Provides audio for up to 40 Valcom one-way
amplified speaker assemblies
 AUX audio input via RCA jack
 Contact closure or VOX operation of audio input
 Removable screw terminal connectors provided
for audio and relay interface
 AUX input music mutes during page
 Output control contact closure provided during
paging output
 Compatible with 25 or 70 Volt amplifiers
 2.5mm jack for optional DC power
 Power over Ethernet (PoE) 802.3af compatible
Dimensions/Weight
 1.38 H x 6.13" W x 5.25" D
(3.50cm H x 15.6cm W x 13.33cm D)
 Weight: 1.25 lbs. (0.57 kg)
Nominal Specifications
Input Impedance: 600 Ohms
Input Level: -10dBm nominal
Voice Switch Sensitivity: -21dBm
AUX Input Impedance: 8 to 600 Ohms
AUX Input Level: -10dBm nominal
Output Impedance: 50 Ohms
Output Level: - 10dBm nominal
Relay Current: 1 Amp @ 24VDC
Nominal Power Requirements
Via rear panel barrel connector:
Voltage: 24VDC
Current: 325mA
Via 802.3af PoE Ethernet Switch:
802.3af: Class 3
Environment
Temperature: 0 to +40° C
Humidity: 0 to 85% non-precipitating
Packing List
Qty Item
1 VIP-801
1 VSP Document
2 Mounting Brackets W/ Hardware
4 Rubber Pads

Valcom VIP-801 Specifications

General

Form factor	Box
Rack mounting	No
Connector type	RJ-45
Supported network protocols	DHCP, IGMP v3, UDP, TCP, HTTP, Telnet, FTP
Compliance industry standards	802.3af
Number of voice channels supported (max)	1
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	0 - 85 %

Weight and Dimensions

Depth	133.3 mm
Width	156 mm
Height	35 mm
Weight	562.5 g

Summary

Introduction to VIP-801

VIP-801 Specifications

Dimensions and Weight

Provides physical dimensions in inches and centimeters, and weight in pounds and kilograms for the VIP-801.

Nominal Specifications

Details input/output impedance, input/output levels, voice switch sensitivity, and relay current ratings.

Nominal Power Requirements

Specifies power needs via barrel connector and PoE, including voltage, current, and PoE class.

Environment Specifications

Outlines operating temperature and humidity ranges for the VIP-801.

Packing List Contents

Lists the items included with the VIP-801 unit, such as the VSP Document and mounting hardware.

Installation and Connections

FCC Information and Precautions

Details FCC compliance for Class A digital devices and general precautionary symbols and warnings.

Mounting Instructions

Provides guidance for table or wall mounting using the included rubber pads and brackets.

Power and Network Connections

Explains preferred power methods (PoE, barrel connector) and network connection via RJ-45.

Signal Connections Overview

Describes rear panel connectors for AUX audio input, audio output, relay connections, and audio input/contact closure.

Setup and Technical Support

VIP-801 Setup Procedure

Instructions for programming the VIP-801 using the IP Solutions Setup Tool via a computer.

Technical Assistance and Troubleshooting

Guidance on reporting issues, contact information for technical support, and troubleshooting resources.

Valcom Limited Warranty

Details the one-year warranty, terms, conditions, exclusions, and disclaimer for Valcom products.