What does peripheral protection mean on a V&T V5-GA-4T2.2G?
If your V&T Inverter indicates peripheral protection, check: * **External failure terminal enabled:** Check the external failure terminal status. * **Stall over voltage or over current lasting more than one minute:** Check whether the external load is normal.
What to do if V&T V5-GA-4T2.2G Inverter has over current protection during deceleration?
If your V&T Inverter displays an over current protection error during deceleration, consider the following: * **Low grid voltage:** Check the input power supply. * **Large rotating inertia of load:** Choose an appropriate dynamic braking unit and braking resistor. * **Improper motor parameters:** Ensure motor parameters are set correctly. * **Short deceleration time:** Prolong the deceleration time. * **Inadequate inverter power level:** Replace the inverter with a model that is more suitable.
Why is my V&T V5-GA-4T2.2G showing an overload protection?
An inverter overload protection error in your V&T Inverter can occur due to several reasons: * **Input power undervoltage:** Check the input power supply. * **Fast start-up with a high-speed motor:** Restart after the motor stops rotating. * **Prolonged overloading:** Shorten the overloading time and reduce the load. * **Short acceleration/deceleration time:** Prolong the acceleration or deceleration time. * **High V/F curve ratio:** Adjust the V/F curve setting and torque boost. * **Inadequate inverter power level:** Replace the inverter with a model that is more suitable.
V&T V5-GA-4T2.2G Inverter: How to resolve over current protection during constant speed operation?
If your V&T Inverter shows an over current protection error during constant speed operation, check these: * **Sudden load changes:** Decrease the load’s abrupt frequency change and amplitude. * **Improper motor parameters:** Ensure motor parameters are set correctly. * **Inadequate inverter power level:** Replace the inverter with a model that is more suitable.
What to do if V&T V5-GA-4T2.2G Inverter shows copy failure?
If your V&T Inverter displays a copy failure message, check: * **Data error when uploading:** Check the connection of the operation panel. * **Data error when downloading:** Check the connection of the operation panel. * **Parametric copy download without parameter upload:** Perform download before uploading the parameters. * **Software version incompatible:** Check if d1.09 is consistent.
What does hardware overload protection mean for V&T V5-GA-4T2.2G?
If your V&T Inverter indicates hardware overload protection, check whether the motor is blocked and consider replacing the inverter with a proper model if necessary.
What does analog input abnormal mean on my V&T V5-GA-4T2.2G Inverter?
If your V&T Inverter is showing an analog input abnormal error, check: * **Analog input voltage is too large:** Check whether the analog input voltage complies with the requirements. * **Analog input circuit failure:** Seek for technical support. * **Analog input circuit signal interfered:** Increase the P6.22?P6.24 AI filtering time.
What does interference protection mean for V&T Inverter?
If your V&T Inverter is severely interfered with by an exterior signal, ask professional technicians to maintain it.
How do I fix heatsink 1 over temperature protection on my V&T Inverter?
If your V&T Inverter displays a heatsink 1 over temperature protection error, check: * **Ambient over-temperature:** Lower the ambient temperature and strengthen ventilation and heat dissipation. * **Blockage of air duct:** Clean the dust, wool, and other foreign objects in the air duct. * **Fan failure:** Check if the fan power cable and fan are normal. * **Inverter module failure:** Seek for technical support. * **Temperature detection circuit failure:** Seek for technical support.
What does module protection mean on my V&T V5-GA-4T2.2G Inverter?
Module protection on your V&T Inverter can be triggered by: * **Output over current:** Check whether the motor and the output connection are short circuited, whether the ground is short circuited, and whether the load is too heavy. * **DC terminal overvoltage:** Check the mains power supply and whether the large inertia load has no function of quick stop at energy consumption brake. * **Loose connection of connectors inside the inverter:** Ask professional technicians to maintain.
Details connections for power supply, circuit breakers, reactors, filters, and motors.
Details the process for changing parameters using the keyboard interface.
Covers fundamental parameters like password, display mode, and control operation.
Lists parameters for motor acceleration, deceleration, and torque control.
Lists fault codes, descriptions, possible causes, and countermeasures.
Provides analysis and solutions for common hoisting equipment failures.
To Next Page
General