The Vax PowerWash 2000W – VPW2 is a powerful pressure washer designed for household outdoor cleaning tasks. It is ideal for tackling cars, large-scale paved surfaces, and patios, providing an effective and efficient cleaning solution.
Function Description:
The pressure washer operates by delivering a high-pressure water jet to remove dirt, grime, moss, and other stubborn debris from various outdoor surfaces. It can be used with different nozzles and accessories to suit specific cleaning needs, from wide-spray cleaning of delicate surfaces to concentrated blasting for heavily soiled areas. The device also supports the use of Vax-specific detergents for enhanced cleaning performance, which can be dispensed through a dedicated solution nozzle or compatible brushes.
Important Technical Specifications:
- Name: 2000W
- Wattage: 220-240V~50Hz
- Max Pressure: 140 bar
- Working Pressure: 100 bar
- Flow Rate: 430L/Hr
Usage Features:
Safety Precautions:
- Intended for household use only, not commercial or industrial.
- For outdoor use only.
- Users are responsible for checking surface suitability to avoid damage.
- Maintain a working distance of 30cm between the nozzle and the surface.
- Keep fingers, hair, and loose clothing away from moving parts.
- Never leave unattended or running for more than 5 minutes without depressing the trigger.
- Do not use if dropped, damaged, or immersed in water, or if the power cord or plug is damaged.
- Do not handle the plug with wet hands.
- Always use with the supply hose (minimum length 7.5m) fully unwound and the water filter in place.
- Do not pull or carry by the power cord, or use it as a handle.
- Do not aim the pressure washer at people, animals, plants, electrical components, wires, or the unit itself.
- Avoid using on electrical components, damaged/delicate paint surfaces, tyres, engines/motors.
- Ensure the correct voltage is used as listed on the rating label.
- Always wear suitable clothing, footwear, and eye protection.
- Always connect the water supply and run water through the machine by squeezing the trigger before switching on.
- Use a suitable hose connector with a non-return valve at the tap end.
- Unplug before cleaning or maintenance.
- Turn off and unplug before disconnecting/connecting the hose.
- Wrap the pressure hose and power cord around storage clips after use.
- Always release built-up pressure in the handle before disconnecting the hose.
- Ensure the water inlet filter is clean before storage.
- Use only CE approved 13amp extension cords with RCD; non-approved cords may overheat. Arrange extension cords carefully to avoid trip hazards.
- Ensure the power/extension cord is fully unwound and kept dry.
- Replace fuses with British 13amp fuses.
- Protect the power cable from heated surfaces or open flames.
- Carry the pressure washer by the handle.
- Regularly check the water hose and accessories for damage.
- Always use an RCD (Residual Current Device) adaptor.
- Before switching on, squeeze the trigger handle to release water and remove airlocks.
- Always release pressure in the handle before disconnecting the hose.
- Always ensure the trigger safety lock is in the LOCKED position when not in use or connecting/disconnecting accessories.
- Always check water hose, pressure hose, lance, and accessories for damage.
- Always switch off the machine and ensure the safety button on the trigger handle is LOCKED before connecting/disconnecting the lance, nozzle, or accessories.
- When using solution, follow dilution instructions and use Vax solution only. Solution cannot be used with jet and turbo nozzles.
Assembly:
- Attach both wheels by pushing until they click into place.
- Attach the hose connector to the water inlet by turning clockwise until tight.
- Slot the handle into the top of the machine and insert the two screws, turning clockwise to tighten.
- Align the pressure hose and cord storage hook onto the back of the machine and secure with two screws.
Preparation for Use:
- Ensure the water supply is not connected. Firmly push the water hose pipe with a suitable connector onto the water inlet to lock it in position.
- Connect the water hose pipe to a suitable water supply and turn on the water.
- Before plugging in, press the unlock safety button on the trigger handle and squeeze the trigger until water flows through the nozzle.
- Connect the power cord to the mains supply via an RCD adaptor.
- Push the pressure hose firmly to the water outlet and turn the pressure hose collar clockwise until tight.
- Ensure the trigger safety lock (located underneath the handle) is in the LOCKED position before connecting the pressure hose to the trigger handle.
- To connect the pressure hose to the trigger handle, press the pressure hose release button and push the hose to lock it in position. Gently pull to check the connection.
- Whilst firmly pushing the lance into the trigger handle, turn clockwise to lock it in position.
- To remove the lance, firmly push and twist it anti-clockwise. When unlocked, pull to remove.
- After connecting the pressure hose, lance, and accessories, check they are securely fitted and locked in place before turning on.
- Push the 'I' switch to turn on. The machine will run for a few seconds then stop, but no water will be released until the trigger is squeezed.
- Squeeze the trigger on the trigger handle to release a high-pressure water jet and begin cleaning.
- Push the 'O' switch to turn off.
Using Accessories:
- Jet Nozzle (Orange Nib): Provides a wider spray, ideal for cars, garden furniture, decking, and boats. To attach, fit the lance with a firm push and twist. Hold down the release button on the lance, push the jet nozzle and lance together until an audible CLICK is heard. Release the button and gently pull to ensure it's locked.
- Turbo Nozzle: Offers a more concentrated spray for very dirty surfaces, patios, or masonry. Not suitable for delicate or painted surfaces as it lacks a pressure regulator. Attachment process is similar to the jet nozzle.
- Solution Nozzle (White Nib): Used for dispensing Vax solutions. Unhook the solution tube and insert it into the solution bag. Switch on the machine and squeeze the trigger to dispense the water and solution mix. After use, rinse the pressure washer by inserting the solution tube into a bucket of fresh water (Max 40°C), turning on the machine, and squeezing the trigger for 1 minute.
Maintenance Features:
Preventing Blockages:
- Always rinse fresh water through the pressure washer and accessories for 1 minute after using solution.
Water Filter Maintenance:
- Unscrew the water inlet connector to access the water filter.
- Pinch the inner water filter tab with pliers and gently pull to remove.
- Rinse the water filter under running water periodically.
Removing Blockages in Lance and Nozzles:
- To remove the lance from the trigger handle, firmly push and twist the lance; when unlocked, pull to remove.
- To remove the nozzles, press the nozzle release button and pull.
- Insert the nozzle cleaning tool into the end of the lance and nozzles to remove any dirt or debris.
Storage:
- Before storing, ensure no water remains in the pressure washer or hose/accessories to prevent frost damage.
- Store in a dry place above zero degrees and out of reach of children.
- Always store tools, power cord, and pressure hose in allocated storage slots.
Troubleshooting:
- Accessory Missing: Check the 'This pack contains' panel on the box.
- Pressure Washer Won't Turn On:
- Ensure on/off switch is in 'I' position.
- Check if the plug is fully pushed into the socket.
- Check and replace the 13amp fuse if needed.
- Reset the RCD if tripped.
- Contact customer care if the power cord is damaged.
- Water/Solution Won't Dispense:
- Ensure on/off switch is in 'I' position and check the plug fuse.
- Check for pump overheating due to poor water supply; check water flow rate.
- Check for blocked/kinked hoses, leaks, and clear any blockages. Straighten hoses and check connections.
- Release airlock by unlocking the trigger safety lock and squeezing the trigger.
- Check assembly of solution application bottle.
- Clear any blockages in the nozzle/accessory.
- Pressure Washer Not Reaching Operating Pressure:
- Check for blocked/kinked hoses, leaks, and clear any blockages. Straighten hoses and check connections.
- Clear any blockages in the nozzle.
- Remove and clean the water inlet filter.
- Check water flow rate.
Accessories & Consumables (available at vax.co.uk):
- Universal detergent (1-9-133398-00)
- Patio & Decking detergent (1-9-133401-00)
- Wash & Protect vehicle detergent (1-9-133400-00)
- Standard lance (1-9-133749-00)
- Detergent nozzle (1-9-133759-00)
- Attachable detergent bottle (1-2-133752-00)
- Trigger handle (1-2-133750-00)
- Jet nozzle (1-9-133754-00)
- Turbo nozzle (1-9-133753-00)
- Patio cleaning set (1-9-133767-00)
- Rotary brush (1-9-133766-00)
- Car brush (1-9-133765-00)
- Outdoor brush (1-9-133769-00)
- Extension bar (1-9-133768-00)
- Replacement hose (10m) (1-9-133751-00)
Need help?
General
To Next Page
