Vector VEC1087 A User Manual

SMART AUTOMATIC
BATTERY CHARGER
12 VOLT 2/6/10 AMP CHARGE RATES
OWNER’S MANUAL & WARRANTY INFORMATION
• IMPORTANT SAFETY INSTRUCTIONS •
WARNING – RISK OF EXPLOSIVE GASES
1. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES
GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS
REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR
CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
2. To reduce risk of battery explosion, follow these instructions and those published by the battery
manufacturer and manufacturer of any equipment you intend to use in vicinity of battery. Review
cautionary markings on these products and on engine.
GENERAL BATTERY SAFETY
1. Use this charger for charging a 12 VOLT LEAD-ACID battery only. It is not intended to supply power to a low voltage
electrical system other than in automotive applications. Do not use this battery charger for other types of batteries,
these may burst and cause injury to persons and damage to property.
2. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire,
electric shock, or injury to persons.
3. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
4. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result
in a risk of fire and electric shock.
If extension cord must be used, make sure:
a. That pins on plug of extension cord are the same number, size, and shape as those of plug on charger.
b. That extension cord is properly wired and in good electrical condition; and
c. That wire size is AWG #14 (14 gauge) to 100 feet and AWG #12 for distances over 100 feet.
5. Do not operate charger with damaged cord or plug - replace immediately.
6. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take
it to a qualified service technician.
7. Do not disassemble charger; take it to a qualified service technician when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
8. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning
off controls will not reduce this risk.
9. Do not expose charger to rain, snow or use when wet.
10. Never charge a frozen battery.
SAVE THESE INSTRUCTIONS:
This manual contains important safety and operating instructions for battery charger Model VEC1087 AA
4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312 • TEL: 954-584-4446 • FAX: 954-584-5556 • TOLL-FREE 866-584-5504
VEC1087 A
This device complies with Part 15 of the FCC Rules.

Vector VEC1087 A Specifications

General

Output Voltage	12V DC
Battery Type	Lead-Acid
Input Voltage	100-240V AC
Charging Modes	Trickle
LED Indicators	Power, Charging
Type	Automatic
Compatibility	12V Lead-Acid batteries
Safety Features	Overcharge protection

Summary

GENERAL BATTERY SAFETY

Safety Instructions

Provides essential safety guidelines for using a 12-volt lead-acid battery charger.

PERSONAL PRECAUTIONS AND SAFETY

Personal Safety Measures

Details personal safety precautions when working near lead-acid batteries and electrical equipment.

GROUND AND AC POWER CORD CONNECTION

AC Power Cord and Grounding

Ensures proper grounding and connection of the AC power cord for safe operation.

PREPARATION AND CONNECTION PROCEDURES

Battery Preparation Steps

Outlines necessary steps to prepare a battery before initiating the charging process.

Charger Location and DC Connection

Specifies charger placement and critical precautions for DC connection to batteries.

INTRODUCTION AND FEATURES

Charging Process Stages

Explains the three distinct charging stages: Rapid Start, Absorption, and Top-Off.

Key Charger Features

Highlights the main features of the Vector Smart Battery Charger, including charge rates and controls.

CONTROLS AND OPERATION

Controls and Indicators Overview

Describes the function of each LED indicator and the charge rate selection button.

Operating the Charger

Provides step-by-step instructions for operating the charger and notes on charging smaller batteries.

CHARGING BATTERY IN VEHICLE

Vehicle Connection Procedure

Details the procedure for connecting the charger to a battery installed in a vehicle, including polarity and grounding.

Extension Cord Safety

Provides important safety information and requirements for using extension cords with the charger.

CHARGING BATTERY OUTSIDE VEHICLE

External Battery Connection

Explains the step-by-step process for charging a battery that has been removed from a vehicle.

CHARGING TIMES AND MAINTENANCE

Estimating Charging Duration

Explains how charging times are automatically adjusted and where to find estimates.

Care and Maintenance

Outlines recommended procedures for maintaining the battery charger for longevity.

TROUBLESHOOTING

Fault LED Troubleshooting

Identifies common conditions that trigger the Fault LED and provides solutions.

Battery Condition Issues

Addresses specific battery problems like sulfation, short cells, and cold temperatures affecting charging.

APPENDIX A - CHARGING TIMES

Charging Time Calculation Guide

Provides charts and formulas to estimate charging times based on battery charge and rate.