Vector VEC1095A User Manual

SMART AUTOMATIC
BATTERY CHARGER
OWNER’S MANUAL & WARRANTY INFORMATION
12 VOLT 2/10/25 AMP WITH 75 AMP ENGINE START
ALTERNATOR VOLTAGE CHECK AND BATTERY RECONDITION
FUNCTIONS
• IMPORTANT SAFETY INSTRUCTIONS •
WARNING – RISK OF EXPLOSIVE GASES
WARNING - RISK OF EXPLOSIVE GASES
1. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE
EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF
UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS
MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
2. To reduce risk of battery explosion, follow these instructions and those published by the battery manufac-
turer and manufacturer of any equipment you intend to use in vicinity of battery. Review cautionary mark-
ings on these products and on engine.
GENERAL SAFETY
1. Use this charger for charging a LEAD-ACID battery only. It is not intended to supply power to a low voltage electrical sys-
tem other than in a starter-motor application. DO not use this battery charger for dry-cell batteries that are commonly used
with home appliances. These batteries may burst and cause injury to persons and damage to property.
2. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric
shock, or injury to persons.
3. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
4. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a
risk of fire and electric shock.
If extension cord must be used, make sure:
a. Pins on plug of extension cord are the same number, size, and shape as those of plug on charger.
b. Extension cord is properly wired and in good electrical condition; and
c. Wire size is AWG#14 (14 gauge) to 100 feet and AWG#12 for distances over 100 feet.
5. Do not operate charger with damaged cord or plug - take to a qualified service technician for replacement of the cord or
plug immediately.
6. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in anyway; take it to a qual-
ified service technician.
7. Do not disassemble charger; contact a qualified service technician when service or repair is required. Incorrect reassem-
bly may result in risk of electric shock or fire.
8. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off
charger controls will not reduce this risk.
9. Do not operate charger in rain or snow or use when wet.
10. Never charge a frozen battery.
SAVE THESE INSTRUCTIONS:
This manual contains important safety and operating instructions for battery charger Model
VEC1095A
4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312 • TEL: 954-584-4446 • FAX: 954-584-5556 • TOLL-
FREE 866-584-5504
VEC1095A
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
US Patent No. 6,822,425

Vector VEC1095A Specifications

General

Brand	Vector
Model	VEC1095A
Category	Battery Charger
Language	English

Summary

IMPORTANT SAFETY INSTRUCTIONS

WARNING - RISK OF EXPLOSIVE GASES

Details the dangers of explosive gases generated by lead-acid batteries during normal operation.

GENERAL SAFETY

General Safety Guidelines

Covers safe usage, handling of cords, extension cords, and avoiding damage or shock.

PERSONAL PRECAUTIONS AND SAFETY

Personal Safety Measures

Essential precautions for working near batteries, including protective gear and acid contact response.

POWER CORD CONNECTION

Grounding and Outlet Requirements

Ensures proper grounding and connection to a 110/120VAC outlet for safe operation.

PREPARING TO CHARGE

Battery Preparation Steps

Steps before charging, including cleaning terminals, adding water, and ensuring ventilation.

CHARGER LOCATION

Optimal Charger Placement

Guidance on where to position the charger for safe and effective operation.

DC CONNECTION PRECAUTIONS

Connecting Battery Cables

Precautions for connecting and disconnecting DC output clamps to battery terminals.

VEHICLE BATTERY CONNECTION SAFETY

Connecting Battery in Vehicle

Detailed steps for safely connecting the charger to a battery installed in a vehicle.

OUTSIDE VEHICLE BATTERY CONNECTION SAFETY

Connecting Battery Outside Vehicle

Instructions for safely connecting the charger to a battery removed from a vehicle.

INTRODUCTION AND FEATURES

Product Overview

Introduction to the Vector VEC1095A charger and its key features and capabilities.

CONTROLS AND INDICATORS

Control Panel Functions

Explanation of buttons and selectors like Battery Type, Charge Rate, and Engine Start.

Diagnostic Indicators

Details on indicators such as LEDs for battery type, float charge, and battery voltage status.

INDICATORS AND FAULT CODES

Digital Display and LED Indicators

Description of the digital display, status LEDs, and their meanings during operation.

Troubleshooting Fault Codes

Explanation of fault codes (F01-F07) and their corresponding troubleshooting steps.

CHARGING THE BATTERY

Charge Rate Selection

How to select and adjust charging rates (2A, 10A, 25A) for different battery sizes.

AUTOMATIC FLOAT CHARGING

Maintaining Battery Charge

Process for keeping a battery fully charged using the float charge feature.

EQUALIZING PROCESS

Battery Equalization Procedure

Steps for equalizing wet batteries to restore cell balance, with critical warnings.

ALTERNATOR VOLTAGE CHECK

Alternator Testing Procedure

How to test the vehicle's alternator for proper function under no-load and load conditions.

ENGINE START FUNCTION

Procedure for Engine Starting

Steps to use the 75 Amp engine start function for quick engine starting.

MAINTENANCE

Charger Care and Storage

Guidelines for cleaning, maintaining, and storing the battery charger to ensure longevity.

TROUBLESHOOTING

Fault Code Troubleshooting

Addresses common fault codes like F01, F03, F05, F06 and general battery charging issues.

Battery Not Accepting Charge

Steps to diagnose and resolve issues when a battery is not accepting a charge.

VERY COLD BATTERY HANDLING

Charging Cold Batteries

Advice on charging batteries in extremely cold temperatures and warnings against charging frozen batteries.

CHARGING TIMES

Estimating Charging Duration

Table and formula for estimating charging times based on battery size and charge rate.

WARRANTY INFORMATION

Limited Warranty Details

Explains the terms, limitations, and coverage of the product warranty.

Warranty Activation and Service

Instructions for activating the warranty and requesting service or repairs.