Velleman E300GSM - User Manual

E300GSM
V. 01 – 04/10/2017 1 ©Velleman nv
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of
the device after its lifecycle could harm the environment. Do not
dispose of the unit (or batteries) as unsorted municipal waste; it
should be taken to a specialized company for recycling. This device
should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Perel! Please read the manual thoroughly before
bringing this device into service. If the device was damaged in transit, do not
install or use it and contact your dealer.
2. Safety Instructions
● This device can be used by children aged from 8 years and above, and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning the use of the device in a safe way and understand the hazards
involved. Children shall not play with the device. Cleaning and user
maintenance shall not be made by children without supervision. ● Indoor use
only. Keep this device away from rain, moisture, splashing and dripping
liquids. ● Risk of electroshock when opening the cover. Touching live wires
can cause life-threatening electroshocks. ● Familiarise yourself with the
functions of the device before actually using it. ● All modifications of the
device are forbidden for safety reasons. Damage caused by user modifications
to the device is not covered by the warranty. ● Damage caused by disregard
of certain guidelines in this manual is not covered by the warranty and the
dealer will not accept responsibility for any ensuing defects or problems.
● Keep this manual for future reference. ● Refer to the Velleman
®
Service and
Quality Warranty on www.velleman.eu.
3. Overview
1. M button
5. SIM card slot
2. antenna
6. USB connector
3. GSM status LED
7. temperature sensor slot
4. power LED
GSM status LED:
 Slow blinking: no GSM signal
 Normal blinking: GSM signal fixed
 Fast blinking: send or receive SMS
4. Power Control Connector
input
output
Input: 110-230 V~
L: live
N: negative
G: ground
Output: 110-230 V~
L: live
N: negative
G: ground
12V: output and alarm sensor input
12V: constant 12 VDC output (max. 200 mA)
S1: wired sensor input 1, NO/NC type
S2: wired sensor input 2, NO/NC type
12V(C): controllable 12 VDC output (max. 200 mA) (only via SMS)
5. Start
● Connect the antenna to the power control. ● Deactivate the SIM card’s PIN
code using your cell phone. ● Install your SIM card (standard format). Make
sure to insert it fully into the slot. ● Connect the temperature sensor if
desired. ● Connect the power input and output. Make sure to cut off the
power supply prior to connecting! ● Reconnect the power. The LED will light
within 3 to 5 seconds.
6. Registering a Phone Number
This power control accepts up to five phone numbers, i.e. one master number
and four auxiliary numbers. The master number has full authorization to
configure the devices. The auxiliary numbers can only be added by the
master number. All configurations are processed by sending an SMS to the
device’s SIM card. The SMS format is #code-1#code-2#.
Register the master number: #00#
Add an auxiliary number: #06#User-number#
Delete an auxiliary number: #15#User-number#
Manually reset the device to delete the old master number if the device
replies [Master number already exists]. Hold the M button pressed for ten
seconds to return to the factory settings.
7. Free-Calling Control
A master or auxiliary number calling the SIM card number is able to switch
the 230 V power on or off for a few seconds.
Call to switch on/off the power output: #09#1#
 When a user is calling, the switched on power will switch off and vice
versa.
Call to switch on/off the power output for a few seconds: #09#2#time#
 Time parameters: 1-1800, i.e. duration 1-1800 seconds.
Switch off calling control function: #09#0#
8. Power On/Off
Any registered user can send an SMS to switch the 230 V power on/off.
Switch on power: #01#0#
Switch off power: #02#0#
9. Delay Control
Automatically switch the 230 V power on/off for a few minutes. Valid only for
the master number.
Switch on power for a few minutes: #12#0#time#0#
Switch off power for a few minutes: #12#0#time#1#
 Time range: 1-720, i.e. duration 1-720 minutes.
Manually switch on/off the device to abort this function automatically.
10. Schedule Control
Automatically switch the 230 V power on/off according to the set schedule.
Valid only for the master number.
Set switch-on schedule: #20#0#day#start-time#end-time#
 It will switch on the power at set time.
 Day: one digit, see table.
value
day
value
day
0
Every day
5
Friday
1
Monday
6
Saturday
2
Tuesday
7
Sunday
3
Wednesday
8
Monday-Friday
4
Thursday
9
Weekend
 Start-time and end-time: four digits (hhmm) in 24h-format.
 Example: #20#0#0#2000#0800# means every day, power on at
20:00, power off at 08:00 the next day.
Activate schedule control function: #19#0#1#
Manually switch on/off the device to abort this function automatically.

Summary

Introduction

Safety Instructions

Overview

M button

Button for manual control and factory reset operations.

Antenna

Connects to the device for GSM signal reception.

GSM status LED

Indicates the GSM network signal status.

Power LED

Indicates the operational power status of the device.

SIM card slot

Slot for inserting the standard format SIM card.

USB connector

Connector for potential service or firmware updates.

Temperature sensor slot

Port for connecting the external temperature sensor.

Power Control Connector

Start

Registering a Phone Number

Free-Calling Control

Power On;Off

Delay Control

Schedule Control

Temperature Control

Temperature Alarm

Wired Sensor Alarm

SMS when sensor alarm on;off

Configure SMS notifications for sensor alarm status.

Change sensor name

Assign custom names to wired sensors for clearer alerts.

Change alarm mode

Set alarm trigger logic for sensors (NC, NO, NO/NC).

Auto Control When Triggered

Advanced Settings

SMS when on;off button pressed

Configure SMS alerts for button press events.

SMS when power lost or restore

Configure SMS notifications for power supply status changes.

SMS when calling operation

Configure SMS alerts for incoming calls.

Reset factory settings

Methods to restore the device to its original factory settings.

SMS Command List

Register master number

SMS command to register the primary master phone number.

Define users

Commands for adding, checking, and deleting user phone numbers.

Power control

SMS commands for switching power on/off via calling.

Delay control

SMS commands for timed power control functions.

Schedule control

SMS commands for setting automated power schedules.

Temp control

SMS commands for activating and configuring temperature control.

Temp alarm

SMS commands for setting and managing temperature alarms.

Sensor alarm

SMS commands for activating and configuring sensor alarms.

Sensor trigger, turn on power

SMS commands for auto power control upon sensor trigger.

SMS notifications

SMS commands for various notification settings.

Check status

SMS commands to query the device's current status.

Reset

SMS command to reset the device to factory settings.

Cleaning and Maintenance

Technical Specifications

Velleman E300GSM Specifications

General

Brand	Velleman
Model	E300GSM
Category	Control Unit
Language	English