Ventec Life Systems VOCSN User Manual (English)

Other manuals for Ventec Life Systems VOCSN

Quick Start Guide2 pages

Clinical And Technical Manual225 pages

Questions and Answers:

S
sarahedwardsAug 28, 2025
What causes a high breath rate alarm on Ventec Life Systems Medical Equipment?
- L
  Lisa EspinozaAug 28, 2025
  If the High Breath Rate alarm activates on your Ventec Life Systems Medical Equipment, ensure the High Breath Rate alarm is set above the patient's breath rate plus spontaneous rate. Check for patient secretions and use Suction therapy to clear them if needed. Empty any excess condensation in the patient circuit. Check the VOCSN Leak monitor and resolve any unintentional leaks. If the device is auto-triggering, adjust the Flow Trigger setting.
T
Thomas BurnettAug 27, 2025
How to troubleshoot a 'Check Patient Circuit' error on Ventec Life Systems VOCSN Medical Equipment?
- R
  Ronald BrewerAug 27, 2025
  If you receive a Check Patient Circuit alarm on your Ventec Life Systems Medical Equipment, run a Pre-Use Test. For Passive circuits, check the VOCSN Leak monitor and resolve any unintentional leaks in the patient circuit or around the patient interface, ensuring the exhalation valve is not obstructed. For Active circuits, ensure the flow sensor tubing is securely connected to the device and the active exhalation valve. If using a nebulizer, install a filter between the nebulizer and the patient circuit exhalation valve. For heated circuits, ensure there is no water accumulation in the tubing or valve. If the problem persists, replace the patient circuit.
T
Tammy OliverAug 27, 2025
What to do if apnea activates on Ventec Life Systems Medical Equipment?
- B
  Brenda NobleAug 27, 2025
  If the Apnea alarm activates on your Ventec Life Systems Medical Equipment, ensure the Apnea alarm is set appropriately, considering the patient’s Breath Rate and spontaneous rate. Also, ensure the Flow Trigger control is set correctly. Check the patient triggered icon and waveforms to see if the patient is attempting to initiate breaths. If not, the alarm is working as intended. Check for issues with patient triggering, such as low drive due to medication, secretions, or excessive mask or cuff leak. For Active circuits, turn on Leak Compensation if needed. If the problem continues, replace the circuit.
A
Amy BurnettAug 26, 2025
What causes patient desaturation when using Ventec Life Systems VOCSN?
- A
  Andrew ParsonsAug 27, 2025
  If you observe patient desaturation while using the Ventec Life Systems Medical Equipment, first ensure the O2 monitoring equipment is connected to the patient. Run a Pre-Use Test. Ensure the patient circuit O2 Tube is properly connected so that the rubber connector is flush against the O2 tube connection side of the device. Also, check that any external oxygen source is properly connected and not depleted. Note that it may take up to 1 hour for oxygen alarms to resolve after fixing an issue with the O2 tube connection.
T
Tricia OrtegaAug 25, 2025
What to do if the Ventec Life Systems Medical Equipment shows a high pressure alarm?
- R
  Rachel MooreAug 26, 2025
  Ensure the High Pressure alarm on your Ventec Life Systems Medical Equipment is appropriately set for the patient's condition. Check for any blockages or obstructions in the circuit and patient airway, such as saturated filters, in-line suction catheters, or patient secretions. If the problem persists, replace the patient circuit.

Ventec Life Systems VOCSN Specifications

General

Oxygen Concentration	21-100%
FiO2 Range	21-100%
Power Source	AC Power, DC Power, Internal Battery
Ventilation Modes	SIMV, CPAP
Weight	18 lb (8.2 kg) with battery
Tidal Volume	50-2000 mL
Respiratory Rate	1-60 BPM
PEEP	0-20 cmH2O
Pressure Support	0-30 cmH2O

Related product manuals

Ventec Life Systems Vocsn V+Pro

194 pages

Ventec Life Systems V-Home

182 pages

Ventec Life Systems VOCSN Clinical Quick Start Guide

Table of Contents

Other manuals for Ventec Life Systems VOCSN

Questions and Answers:

Ventec Life Systems VOCSN Specifications

Related product manuals