To Next PageTo Next Page
Need help?Do you have a question about the Vermont Castings Stardance SDDVT Series and is the answer not in the manual?
General| Fuel Type | Natural Gas or Propane |
|---|---|
| Venting | Direct Vent |
| Model | SDDVT Series |
| Ignition Type | Electronic |
| Finish | Enamel |
| Warranty | Limited Lifetime Warranty |
Safety information for Massachusetts and California installations.
Crucial safety warnings for operation, placement, and handling.
Specific Massachusetts codes for CO detectors, signage, and inspections.
Requirements for provided and non-provided venting systems.
Visual representation of the stove's physical dimensions.
Guidance on choosing a location and general installation notes.
Essential spacing requirements for safe installation near combustibles.
Guidelines for hearth flooring and preparation.
Visual guides for parallel and corner installation clearances.
Details on gas types, input/output pressures, and altitude adjustments.
Requirements for horizontal vent runs and termination locations.
Rules for vertical vent runs, elbows, and termination height.
Instructions for adjusting the restrictor plate for optimal flame.
Critical spacing rules around the vent terminal for safety.
Guidance on choosing a safe and effective vent termination location.
Detailed diagram of vent termination clearances.
Procedures for connecting to an existing Class A metal chimney.
Lists approved HHT and DuraVent components for venting.
Step-by-step guide for assembling the stove unit.
Crucial safety notes and code compliance for venting.
Overview of venting requirements and component usage.
Steps for connecting the initial vent pipe to the stove.
Instructions for connecting vent pipe sections securely.
Guidelines for supporting vertical and horizontal vent pipes.
Procedure for separating vent pipe sections.
Steps for attaching the horizontal vent termination cap.
Methods to prevent water damage at horizontal terminations.
Detailed steps for venting through a side wall.
Installation steps for snorkel kits in below-grade situations.
Guidelines for vertical vent runs, offsets, and roof penetration.
Table specifying minimum vent height based on roof pitch.
Procedures for connecting to an existing Class A metal chimney.
Steps for inspecting and preparing masonry chimneys.
Instructions for venting through an existing masonry chimney.
Steps to remove safety barrier and glass frame.
Step-by-step guide for placing logs on the burner.
Table specifying wire gauge based on lead length.
Instructions for wiring the thermostat to the gas valve.
Requirements for proper electrical grounding of the appliance.
Detailed instructions for connecting gas supply lines for Natural Gas and Propane.
Wiring details for the Intellifire™ Touch ignition system.
Guidance on wiring optional accessories.
Steps for attaching the protective safety barrier screen.
Final steps for installing mesh and grille components.
General guidance on operating the stove and initial lighting.
Instructions for checking pilot, burner flames, and adjusting temperature.
Critical safety warnings and instructions before lighting the pilot.
Detailed procedure for safely lighting the pilot and burner.
Specific troubleshooting for the SIT NOVA 820 millivolt valve.
Crucial safety information to read before attempting to light.
Specific instructions for the intermittent pilot ignition system.
Procedure for safely shutting off gas to the appliance.
Steps to operate the appliance using the battery backup system.
Procedure to switch back to standard electrical power.
In-depth guide to operating the IFT-ECM module.
Information on safety features and how to reset the IFT-ECM.
Procedure to reset the IFT-ECM after a lock-out error.
Overview of remote control functions for appliance operation.
Troubleshooting common remote control communication problems.
Explanations for various appliance messages and behaviors.
List and explanation of ECM LED error codes.
Diagnosing issues with pilot ignition and spark generation.
Troubleshooting problems with burner ignition and flame.
Diagnosing intermittent cycling or unexpected shutdowns.
Visual checks for proper pilot flame presence and appearance.
Guidance on checking burner flame color and making adjustments.
Recommendations for annual professional inspection of the heater and venting.
Cleaning and maintenance for logs, burners, and cast iron surfaces.
Instructions for cleaning the glass and replacing it if necessary.
Steps for replacing the tadpole-type gasket on the glass frame.
Procedure for annual inspection of the vent system.
Guidance on regularly checking the burner flame appearance.
Diagrams for On/Off switch and thermostat circuits.
Wiring diagram for the optional blower kit.
Detailed wiring diagram for the Intellifire™ Touch system.
Illustrated list of service parts for the STARDANCE DV.
Part numbers for log sets, burner, and related components.
Part numbers for doors, glass frame, and hardware.
Part numbers for gas valve, pilot assembly, and orifices.
Part numbers for control modules, ignitors, and wiring.
Illustrated list of service parts for the STARDANCE IFT.
Part numbers for log sets, doors, and related hardware.
Part numbers for valves, pilot assemblies, and control modules.
Part numbers for ignitors, safety barriers, and transformers.
Part numbers for blower assembly, touch-up paint, and shelves.
Part numbers for fuel conversion kits and regulators.
Information and part numbers for fan kits and remote controls.
Instructions for installing the optional warming shelf.
Details of the limited lifetime warranty coverage.
Table outlining warranty periods for different components.
Terms and conditions for warranty coverage to remain valid.
List of conditions and damages not covered by the warranty.
Information on the EnerGuide gas fireplace efficiency rating.
DOE and CSA-based efficiency percentages for models.
