This document provides the instruction manual for a VEVOR Wire Stripping Machine, model 038-MDA. VEVOR emphasizes its commitment to providing tools at competitive prices, noting that expressions like "Save Half" are estimates of potential savings compared to major brands. Users are encouraged to verify actual savings when purchasing.
Function Description
The VEVOR Wire Stripping Machine is designed to strip the insulation from various types of wires. Its primary function is to efficiently remove the outer skin of wires without damaging the inner copper core, facilitating the recycling or reuse of copper. The machine features multiple feeding holes to accommodate different wire diameters, ensuring versatility in its application. It is important to note that this machine is not suitable for silicone rubber cables or armored cables.
Important Technical Specifications
- Model: 038-MDA
- Dimensions (LWH): 480 × 165 × 310 mm
- Weight: 15.5 kg
- Voltage:
- Power: 60 W
- Stripping Range: Ø1~Ø25 mm
- Parts List:
- M12 Plastic screw
- Nut for regulating blade up and down
- Right cover
- Transparent incoming Panel
- Baseplate
- Left cover
- Motor
- Front Panel
- Accessories:
- One blade
- Plastic exhaust nut of reducer
Usage Features
The machine is designed for straightforward operation, with several features to ensure effective wire stripping:
- Wire Diameter Selection: Users must select the appropriate feeding hole based on the wire's diameter. The available feeding holes are marked for various ranges: 8×16, Ø1~Ø3, Ø3~Ø5, Ø6~Ø9, Ø10~Ø12, Ø12~Ø15, and Ø16~Ø25 mm.
- Blade Alignment: For optimal stripping, the center of the blade must be collinear with the center of the roller. This alignment is crucial for clean cuts and to prevent damage to the wire.
- Blade Depth Adjustment: The distance between the blade and the rolling shaft can be adjusted according to the wire's thickness. This adjustment is made using the M12 plastic handle screw, which controls the blade's height via a spring assembly. The goal is to cut only the wire skin without harming the copper core.
- Troubleshooting for Stripping Issues:
- If the machine fails to strip the wire, or if the stripped wire's diameter is too small, it may indicate that the blade's center is not aligned with the rolling shaft's center. To address this, users need to remove the shields on both sides of the machine and use a wrench to adjust the screw on the center adjustment block, ensuring the blade is on the same line as the rolling shaft.
- Another reason for poor stripping performance could be a dull blade. In such cases, the blade needs to be replaced following the operating instructions.
Maintenance Features
Proper maintenance is essential for the longevity and safe operation of the wire stripping machine. The manual outlines several key safety and maintenance guidelines:
- General Safety:
- Always read and follow all instructions before using the machine.
- To prevent electrical shock, do not immerse the machine in water or other liquids.
- Clean the motor housing with a damp cloth.
- Children should not play with the appliance, and cleaning/maintenance should not be performed by children without supervision.
- Unplug the machine from the outlet when not in use, before installing/removing parts, and before cleaning.
- Avoid contact with moving parts.
- Do not operate the machine with a damaged cord or plug, or if it malfunctions, is dropped, or damaged. Return it to an authorized service facility for repair.
- Do not use attachments not sold by the manufacturer, as this may cause fire, electric shock, or injury.
- Do not use outdoors.
- Do not allow the cord to hang over the edge of a table or counter.
- Never run the machine unattended.
- If the supply cord is damaged (Type Y attachment), it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid hazards.
- Never put your hand into the machine while it is running. Always stop the machine before checking, debugging, or troubleshooting.
- To avoid cutting your hand, do not touch the blade directly with your hand.
- Environmental Protection: The product is subject to European Directive 2012/19/EC. The crossed-out wheelie bin symbol indicates that the product requires separate refuse collection in the European Union. It should not be discarded with normal household waste but taken to an electrical and electronic equipment collection point for recycling.
For any product questions or technical support, users are encouraged to contact CustomerService@vevor.com. VEVOR reserves the right to update technology or software without prior notice, and the appearance of the product may vary.
To Next Page
Need help?
General
