VEVOR CL-600 - User Manual

Questions and Answers

A
Ashley GlassAug 10, 2025
Why is my VEVOR Chiller refrigerating capacity reduced?
- M
  Melinda WoodAug 10, 2025
  Reduced refrigerating capacity in your VEVOR Chiller after prolonged use can stem from refrigerant leakage or insufficient refrigerant levels, poor heat dissipation, or dust accumulation blocking the condenser radiator fins. Contact a certified technician to inspect and replenish the refrigerant. Improve heat dissipation and air ventilation. Also, clear any dust from the air inlet and other components, and reduce the water volume according to the specifications.
R
ronald73Aug 15, 2025
What to do if my VEVOR CL-600 compressor stops working?
- K
  Katherine GordonAug 15, 2025
  If the compressor on your VEVOR Chiller stops, it could be due to high air and water temperatures causing high internal pressure, a faulty heat protector, or capacitor failure. Try improving heat dissipation and air ventilation. If the problem persists, replace the capacitor or heat protector.
C
Christopher GarciaAug 21, 2025
How to calibrate the water temperature on my VEVOR Chiller?
- R
  Ryan AdamsAug 21, 2025
  If the displayed water temperature on your VEVOR Chiller differs from the actual water temperature, you can calibrate it. Press and hold the “SET” button for 10 seconds to enter the Temperature Error Adjustment Function. The display will show “CA”. Use the up or down arrows to adjust the displayed figure to match the difference between the actual and displayed temperatures (tolerance CA = actual water temp - displayed water temp), within a range of +4 to -4. After 10 seconds without adjustment, the control panel will show the adjusted temperature.
R
Rebecca McguireAug 28, 2025
What to do if my VEVOR CL-600 Chiller continues to run after reaching the set temperature?
- D
  Deborah HughesAug 28, 2025
  If your VEVOR Chiller continues to run even after reaching the set temperature, the temperature sensor may be incorrectly placed or faulty. Turn off or replace the heating switch. Refer to the operating instructions to adjust the temperature control.
L
Lacey JacksonSep 3, 2025
How to troubleshoot a VEVOR Chiller with a blank LCD screen?
- L
  Lisa RogersSep 3, 2025
  If the LCD on your VEVOR Chiller isn’t displaying anything and the machine isn’t working, it could be due to a bad power connection, a blown fuse, or a broken circuit. Replace the fuse, check the power switch and plug, and ensure the unit is plugged into an outlet with the correct voltage and frequency.

Summary

Safety Precautions

General Operation Risks

Highlights risks from improper operation leading to personal injury, machine damage, or object damage.

Electrical Safety Guidelines

Instructions on using appropriate power supplies and handling the power cord safely to prevent electrical hazards.

Operational & Handling Warnings

Safety advice for abnormal conditions, disassembly, air inlet use, and power cord management.

Technical Parameters and Performance

Technical Specifications

How to Use the Water Chiller

Pre-operation Checks

Adjusting Water Temperature

Guide on plugging in, turning on, and using the control panel to set desired water temperatures.

Chiller Operation Modes

Explains how the chiller selects cool/heat mode, indicator lights, and temperature regulation logic.

Important Attentions

Installation and Environment Safety

Operational Safety and Handling

Circuit Diagram and Troubleshooting

Troubleshooting Common Failures

Identifies common issues like LCD display problems or compressor stoppage and provides solutions.

Temperature Calibration and Error Codes

Instructions for calibrating displayed water temperature and addressing error codes like 'E1'.

VEVOR CL-600 Specifications

General

Model	CL-600
Temperature Range	64-90°F / 18-32°C
Refrigerant	R134a
Suitable Water Pipe	8 mm
Temperature Control Accuracy	+/- 1°C
Flow Rate	10L/min
Noise Level	≤50dB