This document describes the VEVOR Animal Trap, a device designed for the humane capture of animals. The trap is part of VEVOR's "Tough Tools, Half Price" line, emphasizing competitive pricing and durability.
Function Description
The VEVOR Animal Trap is a cage-style trap used to capture animals. Its primary function is to safely contain an animal once it enters the trap, preventing escape. The trap operates on a mechanism that triggers a door closure when an animal interacts with a bait plate inside the cage. This allows for the capture of animals without causing them harm, making it suitable for relocation or other management purposes. The design includes features to secure the captured animal and facilitate its transport.
Usage Features
The VEVOR Animal Trap is designed for straightforward assembly and operation, though users are advised to exercise caution during setup.
- Assembly: The trap requires assembly, which involves unfolding the cage and securing its components. Users should wear gloves during installation to prevent injury from sharp edges or moving parts like the pull rod and pedal. Nylon cable ties are provided to reinforce the back door, a critical area where wild animals might attempt to escape. The assembly process involves several steps:
- Cutting the cable ties that hold the collapsed cage.
- Flipping the cage over and lifting it to form its basic structure.
- Pulling down and locking the back plate into place.
- Inserting a short metal rod through designated holes and hooking it around the side of the cage. This rod is then slid towards the bottom of the bait plate and hooked around a clip, completing the setup of the back mechanism.
- Turning the cage to face the front.
- Lifting the trap door spring and pushing it towards the bait plate.
- Placing bait behind the bait plate.
- Securing the metal rod using pre-attached metal folding tags.
- Setting the trap by holding the trap door in an open position, swinging the setting hook beneath the bush on the trap door, and then lowering the door to release pressure onto the setting hook.
- Placement and Relocation: Once set, the trap should be left in position for at least 7 days before relocating. This allows animals to become accustomed to its presence and increases the likelihood of capture. The trap is equipped with carrier handles at the top for easy and safe transport of the captured animal.
- Safety Precautions:
- Assembly Safety: Always assemble the trap according to the provided instructions. Improper assembly can create hazards. Wear ANSI-approved safety goggles and heavy-duty work gloves during installation. Ensure the assembly area is clean and well-lit, and keep bystanders away. Do not assemble the trap when tired or under the influence of alcohol, drugs, or medication. The product's capabilities are only guaranteed when it is properly and completely assembled. Assemble on a flat, level, hard, and smooth surface that can safely support a fully loaded animal trap.
- Usage Safety: To prevent serious injury and death from tipping, users are explicitly warned not to sit or stand on the trap. This product is not a toy and should be kept out of reach of children and pets. Small spare parts should also be kept away from children. The trap must only be used on a flat, level, hard, and smooth surface capable of safely supporting a fully loaded animal trap. Use the trap only as intended. Inspect the trap before every use; do not use it if any parts are loose or damaged. It is recommended that two or more people install the trap.
- Baiting: Bait should be placed behind the bait plate to entice the animal into the trap. The specific type of bait will depend on the target animal.
Maintenance Features
While the manual does not explicitly detail maintenance features, general care for an animal trap typically involves:
- Inspection: Regular inspection before each use is crucial to ensure all parts are secure and undamaged. This includes checking for loose components, bent wires, or any signs of wear that could compromise the trap's effectiveness or safety.
- Cleaning: After each use, especially after an animal has been captured, the trap should be cleaned to remove any scent or residue that might deter future captures or spread disease. A thorough cleaning with water and a mild disinfectant is usually sufficient. Ensure the trap is completely dry before storage to prevent rust.
- Storage: Store the trap in a dry place to prevent corrosion. The collapsible design of the trap (as indicated by the initial assembly steps) suggests it can be folded down for compact storage when not in use, which helps protect it from environmental elements and extends its lifespan.
- Repair/Replacement: If any parts are found to be loose or damaged during inspection, they should be repaired or replaced before the trap is used again. The manual advises against using a damaged trap.
The VEVOR Animal Trap is a practical tool for animal management, emphasizing user safety and effective capture through its design and operational guidelines. Users are encouraged to refer to the technical support and e-warranty certificate available at www.vevor.com/support for further assistance.
To Next Page
Need help?
General
