VEVOR WX440-1 - User Manual

Questions and Answers

J
Joseph JohnsonAug 7, 2025
What to do if the VEVOR WX440-1 Chain Hoists motor does not turn when pressing the remote?
- B
  Brian WilsonAug 7, 2025
  If the motor doesn't turn when you press the remote control button, here are a few things to check: * Ensure the power supply is on. * Inspect the cable connections for any breaks or looseness, and repair if needed. * Examine the switch for faults; repair or replace it if necessary. * Consider capacitor damage, replace it, if needed. * For rise button failures, verify the limit frame is reset or the travel switch is in order. * Also, make sure the emergency stop switch is reset.
J
Jenna ScottAug 15, 2025
Why is my VEVOR Chain Hoists motor noisy and not starting normally?
- L
  Logan MillerAug 15, 2025
  If your motor is noisy and not starting normally after pressing the remote, the issue might be: * The power supply voltage being too low, in that case you should adjust it. * Capacitor damage, which would require replacing the capacitor. * Poor contact in the remote control switch, which means you should repair or replace the switch.
R
Robert AdkinsAug 23, 2025
What to do if there is electrification of VEVOR WX440-1 machine casing?
- L
  Laurie DanielsAug 23, 2025
  If the machine casing is electrified, it could be due to: * A faulty or ungrounded ground. Check and repair the ground cable. * An internal conductor grounded with the housing. Check and repair the internal cables.
G
Gordon NelsonAug 30, 2025
What to do if the lifting instruction is contrary to the execution result in VEVOR WX440-1?
- L
  Luis NelsonAug 30, 2025
  If the lifting instruction is contrary to the execution result, it means that improper operation caused the wire rope to reverse wrap around the drum. Press the lift switch to make the hook drop to the bottom and the wire rope completely out of the rope barrel, and then start the normal work.

Summary

IMPORTANT SAFEGUARDS

General Safety Precautions

Key warnings, precautions, and FCC compliance statements for safe operation.

Basic Safety Information

Fundamental safety guidelines covering usage, installation, and load handling.

PRODUCT PARAMETERS

PRODUCT COMPONENTS

Electric Hoist Unit

The main electric hoist motor and drum assembly.

Mounting Hardware

Includes fixing rings and screws/gaskets for installation.

Lifting Accessories

Sling straps and a hook for lifting operations.

INSTALLATION INSTRUCTIONS

Mounting the Hoist

Procedure for securely installing the electric hoist onto a beam.

Operating Modes Configuration

Guidance on setting up single line or double line operating modes.

Pre-Test Checks

Essential steps before testing the hoist, like removing protective tape.

TROUBLE SHOOTING

Motor Issues: No Turn or Noisy Start

Diagnosing and resolving problems with the motor not turning or starting.

Brake Performance Problems

Addressing brake failures, excessive slip, or noise during operation.

Electrical and Mechanical Faults

Troubleshooting casing electrification, limit mechanism faults, and rope issues.

MAINTENANCE AND REPAIR

Routine Maintenance Procedures

Steps for regular care, including cleaning, lubrication, and component checks.

Frequent Inspection Guidelines

Regular checks for operating mechanisms, brakes, hooks, and ropes.

Periodic (Thorough) Inspection

Detailed annual inspection of critical components and fasteners.

Storage Inspection

Procedures for inspecting hoists that have been idle for extended periods.

Testing

Pre-Use and Loaded Testing

Steps for testing repaired, unused, and loaded hoists before operation.

Limit Device Calibration

Verifying the proper function and trip settings of limit devices.

Summary

IMPORTANT SAFEGUARDS

General Safety Precautions

Key warnings, precautions, and FCC compliance statements for safe operation.

Basic Safety Information

Fundamental safety guidelines covering usage, installation, and load handling.

PRODUCT PARAMETERS

PRODUCT COMPONENTS

Electric Hoist Unit

The main electric hoist motor and drum assembly.

Mounting Hardware

Includes fixing rings and screws/gaskets for installation.

Lifting Accessories

Sling straps and a hook for lifting operations.

INSTALLATION INSTRUCTIONS

Mounting the Hoist

Procedure for securely installing the electric hoist onto a beam.

Operating Modes Configuration

Guidance on setting up single line or double line operating modes.

Pre-Test Checks

Essential steps before testing the hoist, like removing protective tape.

TROUBLE SHOOTING

Motor Issues: No Turn or Noisy Start

Diagnosing and resolving problems with the motor not turning or starting.

Brake Performance Problems

Addressing brake failures, excessive slip, or noise during operation.

Electrical and Mechanical Faults

Troubleshooting casing electrification, limit mechanism faults, and rope issues.

MAINTENANCE AND REPAIR

Routine Maintenance Procedures

Steps for regular care, including cleaning, lubrication, and component checks.

Frequent Inspection Guidelines

Regular checks for operating mechanisms, brakes, hooks, and ropes.

Periodic (Thorough) Inspection

Detailed annual inspection of critical components and fasteners.

Storage Inspection

Procedures for inspecting hoists that have been idle for extended periods.

Testing

Pre-Use and Loaded Testing

Steps for testing repaired, unused, and loaded hoists before operation.

Limit Device Calibration

Verifying the proper function and trip settings of limit devices.

VEVOR WX440-1 Specifications

General

Brand	VEVOR
Model	WX440-1
Category	Chain Hoists
Language	English

Related product manuals

VEVOR WX440-1 - User Manual

Table of Contents

Questions and Answers

Summary

IMPORTANT SAFEGUARDS

General Safety Precautions

Basic Safety Information

PRODUCT PARAMETERS

PRODUCT COMPONENTS

Electric Hoist Unit

Mounting Hardware

Lifting Accessories

INSTALLATION INSTRUCTIONS

Mounting the Hoist

Operating Modes Configuration

Pre-Test Checks

TROUBLE SHOOTING

Motor Issues: No Turn or Noisy Start

Brake Performance Problems

Electrical and Mechanical Faults

MAINTENANCE AND REPAIR

Routine Maintenance Procedures

Frequent Inspection Guidelines

Periodic (Thorough) Inspection

Storage Inspection

Testing

Pre-Use and Loaded Testing

Limit Device Calibration

Summary

IMPORTANT SAFEGUARDS

General Safety Precautions

Basic Safety Information

PRODUCT PARAMETERS

PRODUCT COMPONENTS

Electric Hoist Unit

Mounting Hardware

Lifting Accessories

INSTALLATION INSTRUCTIONS

Mounting the Hoist

Operating Modes Configuration

Pre-Test Checks

TROUBLE SHOOTING

Motor Issues: No Turn or Noisy Start

Brake Performance Problems

Electrical and Mechanical Faults

MAINTENANCE AND REPAIR

Routine Maintenance Procedures

Frequent Inspection Guidelines

Periodic (Thorough) Inspection

Storage Inspection

Testing

Pre-Use and Loaded Testing

Limit Device Calibration

VEVOR WX440-1 Specifications

Related product manuals