Vi.Be.Mac 3022WB406 - User Manual

To Next Page

3022CS AUTOMATIC UNIT

INSTRUCTIONS FOR “VIBEMAC 3022WB406” AUTOMATIC UNIT WITH

LS01PMG DIGITAL PANEL

INTRODUCTION

Thank you for buying this industrial sewing machine of VI.BE.MAC. S.p.A.

Before starting to operate with this automatic unit, please read carefully the following instructions so as to help you to

understand the working of the machine.

These will explain you the working system that must be followed according to the current regulations.

• Any part of this manual can be copied or transcribed without forwarding the application to VI.BE.MAC. S.p.A.

• The content of this handbook can be subject to alterations without notice.

To ask for a new manual or have explanations on every information or technical note presented in this volume, please

contact:

VI.BE.MAC. S.p.A.

TECHNICAL DEPARTMENT

Via Monte Pastello 7/ I

37057 S. GIOVANNI LUPATOTO

(VERONA) - ITALIA

Phone +39 045 8778151

Fax +39 045 8779024

E-mail: vibemac@vibemac.com

Web site: http://www.vibemac.com

In case of followings improvements, some incongruities on technical notes might appear in this manual. Therefore, we

suggest You always to contact our Tech. Dept. to check if new version of this manual or new deepening are available.

“Suggestions on possible mistakes and signalling to improve this handbook will always be welcomed”

Morandin Dario

3022 406 001 A Version

Main Page

Brand	Vi.Be.Mac
Model	3022WB406
Category	Sewing Machine
Language	English

Vi.Be.Mac 3022WB406 - User Manual

Table of Contents

Summary

LS01;PMG LOGIC PANEL

FRONTAL KEYBOARD DESCRIPTION

SET CUT AND UNSTITCHING COUNTERS (PROGRAM 3)

INITIAL UNSTITCHING LENGHT MATERIAL INSERTION (PROGRAM 3)

INITIAL UNSTITCHING LENGHT PRESSER FOOT LOWERING (PROGRAM 3)

STARTING POSITION OF FINAL UNSTITCHING (PROGRAM 3)

LENGTH OF FINAL UNSTITCHING COUNT (PROGRAM 3)

INITIAL CUTTING COUNT (PROGRAM 3)

FINAL CUTTING COUNT (PROGRAM 3)

START PINCER DELAY COUNT (PROGRAM 3)

SET CUT AND UNSTITCHING COUNTERS (PROGRAM 4)

INITIAL UNSTITCHING LENGHT MATERIAL INSERTION (PROGRAM 4)

INITIAL UNSTITCHING LENGHT PRESSER FOOT LOWERING (PROGRAM 4)

START POSITION FINAL UNSTITCHING COUNT (PROGRAM 4)

COUNT FINAL UNSTITCHING LENGTH (PROGRAM 4)

INITIAL CUTTING COUNT (PROGRAM 4)

FINAL CUTTING COUNT (PROGRAM 4)

PROGRAMMING OF THE BASIC PANEL

DIRECT PROGRAMMING OF IMPULSES PER STITCH

TEST FUNCTION

INPUTS CONTROL FROM PHOTOCELL OR DETECTOR

INPUTS CONTROL FROM THE MOTOR PANEL

INPUTS CONTROL TO THE ELECTROVALVES

AUTOMATIC SPEED AND MOTOR STOP CONTROL

SET THE DURATION OF THE CUTTING IMPULSE

MITSUBISHI SERVOMOTOR

POSITIONER

TYPE FMFY PANEL

SETTING OF THE NEEDLE MACHINE STOP POSITION

SETTING OF THE SPEED STITCHING MACHINE

SETTING OF MAXIMUM SEWING SPEED-POSITIONING-CUTTING

SETTING OUTPUT IMPULSE NUMBER FOR STEP BY STEP MOTOR

INPUTS;OUTPUTS TEST

LIST OF ERRORS

LIST OF PARAMETERS

ELECTRO VALVES

PINCER

SAFETY

SAFETY MICRO SWITCH

CYLINDERS

CUTTING

SAFETY CUTTING

PRESSER FOOT LIFTER

PULLER

UNSTITCHING

PULLING MATERIAL DEVICE

UPPER RUBBER ROLLER - PULLER

ADJUSTING OF THE POSITION

LOWER TOOTHED ROLLER

FOLDER

POSITION

ADJUSTMENT OF THE PRESSER FOOT PRESSURE

ADJUSTMENT OF THE MECHANICAL EQUIPMENT

CUTTING DEVICE

ADJUSTMENT OF THE MOVABLE KNIFE POSITION

ADJUSTMENT OF THE CUTTING PRESSURE

UNSTITCHING DEVICE

UNSTITCHING LATTEN ADJUSTMENT

MECHANICAL ADJUSTMENT OF THE SEWING HEAD

NEEDLE BAR HEIGHT

NEEDLE PLATE

POSITION AND HEIGHT OF THE GUIDING SLIT NEEDLE PLATE

ECCENTRIC FOR NEEDLE BAR TRANSLATION MOVEMENT

MOVEMENT LENGTH

NEEDLE BAR PENDULUM POSITION

ECCENTRIC OF THE LOOP STARTINGS MOVEMENT

DISTANCE BETWEEN LOOPER- NEEDLE

SPREADER PHASE

POSITION

LENGTH OF MOVEMENT

POSITION OF THE SPREADER MOVEMENT PIN

POSITION OF THE SPREADER

STITCH LENGTH

ADJUSTMENT OF THE LOWER ROLLER PROFILED PLUGS

CLEANING

LUBRICATION

ELECTRICAL CONNECTION