Videx 3000 Series User Manual

66251111 - V5.0 - 15/03/23
- 1 -
3000 Series
Art.3187 - Installation instructions
85
55
218
D
A A
C
B B
Art.3187 Art.3187/8
Fig. 1
BUS
BUS
GND
LB
AL
5
4
3 8
7
6
ON
2
1
4
3
ON
2
1
SW1SW3
S1
E
G
H
F
Fig. 2
DESCRIPTION
Intelligent intercom with door open, intercommunicating call
or services push buttons (programmable) and call tone volume
control (3 levels). To reduce bus current all apartment devices
are in a sleep mode when not used. In case a user forgot to re-
place the handset, each operation must be executed within 10
seconds of lifting the handset otherwise the handset returns to
its sleep state. To then perform an operation it would be neces-
sary to hang up the handset and pick it up again.
LEGEND
A
Door open button
Intercommunicating call/service address switch (only Art.3187/8)
B
Intercommunicating call buttons or service buttons
C
Intercommunicating call/service address switch LED
(only Art.3187/8)
D
Call tone volume control
E
Intercommunication setting switches (SW3)
F
Unit address switches (SW1)
G
Impedance terminator (S1)
H
Connection terminals
PUSH BUTTONS
Door open button
During a conversation, with the handset lifted, press to
operate the lock.
Intercommunicating call/services addresses switch
(Only Art.3187/8)
In stand-by mode, pick up the handset then press to switch
between addresses range 1-4 (LED
C
switched o) or 5-8
(LED
C
illuminated).
Intercommunicating call buttons (SW1 - Dip 8 = OFF)
Pick up the handset then press the call button for the re-
quired phone to be called. To call addresses from 5 to 8, rst
press the button.
1-8 Service buttons (SW1 - Dip 8 = ON)
Pick up the handset then press the service button for the re-
quired relay to activate. To select service addresses from 5 to
8, rst press the button.
Activate the outdoor station 2
nd
output
During a conversation, press this button once to activate the secondary relay of outdoor station (only with Art.4304, 4304X,
4384 and 4384X PCB Rev.0.1).
Art.3187 - Art.3187/8
Intercommunicating intercom for VX2300 digital system

Videx 3000 Series Specifications

General

Brand	Videx
Model	3000 Series
Category	Telephone
Language	English

Summary

Product Overview and Operation

Product General Description

Intelligent intercom features, intercommunicating calls, and programmable service push buttons.

Push Buttons and Functionality

Details on door open, intercommunicating call, and 2nd output activation buttons.

System Component Legend

Identifies key components (A-H) including switches, controls, and terminals.

Configuration and Settings

LED Indicator Functionality

Explains the address switch LED on Art. 3187/8 for range indication.

Call Tone Volume Adjustment

Details the 3-level call tone volume control (D).

Device Address Programming SW1

Sets unit address using SW1 DIP switches with binary to decimal conversion for addresses 1-99.

Intercommunication Setting SW1 Dip 8

Configures SW1 Dip 8 for intercommunication or service button activation.

Advanced Settings and Specifications

Intercommunication Settings SW3

Configures intercommunication modes within same or different apartments using SW3.

Number of Rings Setting

Procedure to set the number of rings to 3 or 6 via LB/GND shorting.

Connection Terminals and Signals

Details on LB, AL, GND, and BUS terminals for system connections.

Technical Specifications Overview

Provides power consumption and working voltage details for the intercom.

Environmental and Company Information

WEEE Disposal Information

Guidance on proper disposal of electrical and electronic equipment (WEEE) per EU directive.

Manufacturer and Company Details

Information about VIDEX ELECTRONICS S.P.A. and its global offices.

Customer Support Contact Information

Contact details for customer support across different regions and countries.

Product Compliance and Certifications

CE marking and conformity with European directives (EMC, LVD, RoHS).