Viessmann VITOCROSSAL 200 Installation Instructions

Viessmann VITOCROSSAL 200

64 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Installation Instructions

VITOCROSSAL 200

6175 796 - 07 10/2022

for use by heating contractor

Vitocrossal 200 CI2 series

Gas condensing boilers with MatriX cylinder burners

Heating input: 399 to 2000 MBH

(117 to 586 kW)

Read and save these instructions

for future reference.

Please file in Service Binder

Product may not be exactly as shown

IMPORTANT

H

Table of Contents

Other manuals for Viessmann VITOCROSSAL 200

Instructions72 pages

Technical Data Manual16 pages

Service Instructions96 pages

Operating Instructions12 pages

Installation Instructions For Contractors32 pages

Service Instructions For Contractors88 pages

Questions and Answers:

J
James WilliamsSep 5, 2025
What to do if Viessmann Boiler burner control unit is in fault state?
- H
  Heather JamesSep 5, 2025
  If the burner control unit in your Viessmann Boiler is in a fault state, here are some potential causes and solutions: * If valve 1 or valve 2 is leaking, replace the gas train. * If there is an internal fault and the fan cannot reach its set value, replace the burner control unit or fan. * If the safety chain has been opened, check the safety chain. * If there is an internal error in feedback from gas safety valves or the output relay does not respond, replace the burner control unit. * If the safety chain is 'live', check the safety chain. * If it is an EMC fault, have your system tested for EMC interference.
D
Daniel WellsAug 25, 2025
What to do if my Viessmann VITOCROSSAL 200 shows F b7 error?
- J
  Jennifer SimmonsAug 25, 2025
  If your Viessmann Boiler displays error code F b7, it might be due to a missing, incorrect, or faulty coding card in the burner control unit. First, ensure the coding card is properly inserted. If it is, check the card for any damage or inconsistencies. If problems persist, consider replacing the coding card.
P
patriciaavilaAug 25, 2025
Why does my Viessmann VITOCROSSAL 200 Boiler display F b7 error if the coding card doesn't match the burner control unit?
- J
  Joseph SteeleAug 26, 2025
  If your Viessmann Boiler displays error code F b7, it may be because the coding card does not match the burner control unit. Replace the coding card or burner control unit. Important: Ensure the power is off before replacing the coding card.
S
Sean GallegosAug 27, 2025
What does error code F 80 mean on my Viessmann VITOCROSSAL 200 Boiler?
- M
  Melanie VasquezAug 27, 2025
  If your Viessmann Boiler shows the error code F 80, it indicates a potential short circuit in the boiler water temperature sensor or burner control unit. Check the lead and dual sensor, and replace the sensor if necessary.
E
Edward PhillipsAug 27, 2025
How to fix Viessmann VITOCROSSAL 200 Boiler error F 82?
- R
  Richard HuntAug 27, 2025
  If your Viessmann Boiler is showing the error code F 82, there may be a short circuit in the flue gas temperature sensor (A or B) or the burner control unit. Check the lead and sensors (A and B), and replace the sensor if needed.
M
moorestephanieAug 28, 2025
What causes error code F 88 on a Viessmann VITOCROSSAL 200 Boiler?
- A
  Ana ThompsonAug 28, 2025
  If your Viessmann Boiler displays the error code F 88, it indicates a lead break in the boiler water temperature sensor or burner control unit. Check the lead and dual sensor; replace the sensor if required.
M
Mary MckinneySep 12, 2025
What to do if Viessmann Boiler air pressure switch shows no air pressure and the fan does not operate?
- S
  shawnlambertSep 12, 2025
  If the air pressure switch shows no air pressure and the fan does not operate on your Viessmann Boiler, replace the air pressure switch and ensure it is correctly connected or set.
T
Thomas HensonSep 12, 2025
What to do if Viessmann VITOCROSSAL 200 Boiler fan does not run?
- D
  Deanna LambertSep 12, 2025
  If the fan of your Viessmann Boiler does not run, check the cables. If the cables are faulty or broken, or the fan itself is faulty, replace the fan if required.
H
haley68Sep 4, 2025
What to do if Viessmann VITOCROSSAL 200 Boiler has no flame signal during the safety time?
- S
  Sara JohnsonSep 4, 2025
  If your Viessmann Boiler shows no flame signal during the safety time, and the ionisation flame monitor reports no flame signal, it could be due to several reasons: * The ionisation electrode may be incorrectly adjusted or the cable may not be plugged in. Adjust the ionisation electrode or plug in the ionisation electrode. * The ignition electrodes may be incorrectly adjusted. Adjust the ignition electrodes. * The insulation body of the ignition electrodes may be cracked. Replace the ignition electrodes. * The incorrect gas type may be selected. Adjust the gas type. * The gas train may not be opening. Check the gas train and replace it if required.
D
Diana KennedySep 2, 2025
What to do if Viessmann VITOCROSSAL 200 burner is OFF due to lack of gas?
- J
  John Johnson MDSep 2, 2025
  If the Viessmann Boiler burner is OFF due to a lack of gas, notify your gas supply company.

Viessmann VITOCROSSAL 200 Specifications

General

Model	VITOCROSSAL 200
Category	Boiler
Installation Type	Floor Standing
Heat Exchanger Material	Stainless Steel
Control	Vitotronic Control Unit
Boiler Type	Condensing
Efficiency	Up to 98%
Modulation	5:1
Max Flow Temperature	90°C
Fuel Type	Natural Gas

Related product manuals

Viessmann Vitocrossal 200 CT2

Preview: Vitocrossal 200 CM2 186

Vitocrossal 200 CM2 186

Preview: Vitocrossal 200 CM2 246

Vitocrossal 200 CM2 246

Preview: Vitocrossal 200 CM2 400

Vitocrossal 200 CM2 400

Preview: Vitocrossal 200 CM2 500

Vitocrossal 200 CM2 500

Vitocrossal 200 CM2 Series

Preview: Viessmann Vitocrossal

Viessmann Vitocrossal

Preview: Viessmann VITOCROSSAL 300

Viessmann VITOCROSSAL 300

Preview: Viessmann VITOCROSSAL Series

Viessmann VITOCROSSAL Series

Preview: Viessmann Vitocrossal 300 Series

Viessmann Vitocrossal 300 Series

Preview: VITOCROSSAL 300 Type CT3

VITOCROSSAL 300 Type CT3

Vitocrossal 300 CT3 SERIES