Viessmann VITODENS - Safety Instructions; General Safety Advice; Appliance Connection and Operation Safety; Work on the Appliance and Damage Prevention

Index
1. Flue systems 1. 1 Flue systems ............................................................................................................... 4
■ Structural unit .......................................................................................................... 4
■ System certification ................................................................................................. 4
1. 2 Balanced flue operation .............................................................................................. 4
1. 3 Open flue operation ................................................................................................... 5
1. 4 Flue gas high limit safety cut-out ................................................................................ 5
1. 5 Lightning protection .................................................................................................... 5
1. 6 CE certification for PPs flue systems (rigid and flexible) for the Vitodens .................. 6
1. 7 Flue installation options for balanced flue operation ................................................... 8
■ In the living space (occupied area) with one or more full storeys above ................ 8
■ In the living space (occupied area), immediately underneath the roof or with only
attics above (rated heating output ≤ 50 kW) ........................................................... 9
■ In the installation room, with ventilation air supplied through the external wall ....... 9
■ Several Vitodens in the living space or in occupied areas (living space - rated heat-
ing output ≤ 50 kW) ................................................................................................. 9
1. 8 Flue installation options for open flue operation ......................................................... 10
■ In the installation room (non-living space) with one or more full floors above (com-
pulsory for the Vitodens 200-W from 60 kW) .......................................................... 10
■ Special version: Open flue operation and installed in the living space (occupied
area) with interconnected room air supply (rated heating output ≤ 35 kW) ............ 11
■ Flue gas header for several Vitodens 200-W, 222-W and 222-F – positive pressure 11
■ Flue gas header for several Vitodens – negative pressure ..................................... 11
2. Design and sizing information for
connection on the flue gas side
2. 2 Plastic (PPs) balanced flue system for routing through a shaft – balanced flue oper-
ation (type C
93x
to TRGI 2008) ....................................................................................
12
■ Internal shaft dimensions to DIN V 18160 .............................................................. 12
■ Flue, system size 60, 80 and 100 (components) (type C
93x
according to TRGI 2008)
14
■ Vitodens in conjunction with solid fuel boilers ......................................................... 15
■ Flue, flexible, system size 60, 80 and 100 (components) (type C
93x
according to
TRGI 2008) ............................................................................................................. 17
2. 3 Plastic (PPs) balanced flue system for vertical routing through a pitched or flat roof
(type C
33x
, to TRGI 2008) ...........................................................................................
18
■ For vertical roof outlets when the Vitodens is installed in attics .............................. 18
■ Vertical flat roof outlet ............................................................................................. 18
2. 4 Plastic (PPs) balanced flue system for external wall connection (type C
13x
to TRGI
2008) ........................................................................................................................... 20
■ Max. total length of the flue pipe ............................................................................. 20
2. 5 Plastic (PPs) flue/ventilation air system for separate ventilation air and flue gas routing
(type C
83x
to TRGI 2008) ............................................................................................
21
2. 6 Plastic (PPs) balanced flue system for routing over external walls (type C
53x
, to TRGI
2008) ........................................................................................................................... 22
2. 7 Plastic (PPs) balanced flue system for routing through a lightweight shaft ................ 24
■ "UNIFIX" shaft profiles offered by Skoberne (made from aerated concrete) .......... 24
■ "SKOBIFIXnano" and "SKOBIFIXXs 30" shaft profiles offered by Skoberne (made
from foamed ceramics) ........................................................................................... 24
■ Anchoring for roof outlets with shaft profiles ........................................................... 25
■ Shaft profiles offered by Promat ............................................................................. 25
■ Roof outlet for shafts with Promat profiles .............................................................. 26
2. 8 Plastic (PPs) balanced flue system for routing multiple pipes through a shaft ........... 26
■ Layout examples ..................................................................................................... 27
2. 9 Plastic (PPs) balanced flue system (connection pipe) for connecting multiple flues to
a single room sealed balanced flue system ................................................................ 27
■ Room sealed balanced flue system, negative pressure (type C
43x
, to TRGI 2008)
28
■ Room sealed balanced flue system, positive pressure – multiple connection with
the Vitodens 200-W, 222-W and 222-F up to 26 kW (type C
43x
to TRGI 2008) ......
28
Index
2
VIESMANN
VITODENS AND VITOSOLAR
5414 641 GB