To Next PageTo Next Page
Need help?Do you have a question about the Viking FPNI515 and is the answer not in the manual?
Essential guidelines for safe operation, covering electrical hazards, fire prevention, and proper handling.
Critical alerts regarding fire, electric shock, and safe appliance usage.
Critical safety warning about the risk of child entrapment in discarded refrigeration units.
Instructions to contact municipal waste disposal authorities for safe disposal methods.
Detailed measurements and diagrams for the ice machine, including overall and cutout dimensions.
Information and diagrams illustrating door swing angles and required clearances.
Technical specifications for the 15"W. Undercounter/Freestanding Nugget Ice Machine.
Required cutout dimensions for installation.
Details on the location of drain and electrical connections for the ice machine.
Guidance on ensuring proper airflow for optimal ice production.
Instructions for attaching custom or accessory door panels.
Procedure for changing the direction of the ice machine door swing.
Instructions for connecting the water supply, including tubing and shut-off valve.
Guidance for both gravity drain and drain pump models, including routing and connections.
Details on the required electrical supply and connection procedures.
Steps to complete the installation, including leveling and initial checks.
A checklist to ensure all installation steps have been completed correctly.
Information on how to contact dealers or authorized service agencies for assistance.
Guidance on recording model and serial numbers for service purposes.
Essential guidelines for safe operation, covering electrical hazards, fire prevention, and proper handling.
Critical alerts regarding fire, electric shock, and safe appliance usage.
Critical safety warning about the risk of child entrapment in discarded refrigeration units.
Instructions to contact municipal waste disposal authorities for safe disposal methods.
Detailed measurements and diagrams for the ice machine, including overall and cutout dimensions.
Information and diagrams illustrating door swing angles and required clearances.
Technical specifications for the 15"W. Undercounter/Freestanding Nugget Ice Machine.
Required cutout dimensions for installation.
Details on the location of drain and electrical connections for the ice machine.
Guidance on ensuring proper airflow for optimal ice production.
Instructions for attaching custom or accessory door panels.
Procedure for changing the direction of the ice machine door swing.
Instructions for connecting the water supply, including tubing and shut-off valve.
Guidance for both gravity drain and drain pump models, including routing and connections.
Details on the required electrical supply and connection procedures.
Steps to complete the installation, including leveling and initial checks.
A checklist to ensure all installation steps have been completed correctly.
Information on how to contact dealers or authorized service agencies for assistance.
Guidance on recording model and serial numbers for service purposes.
This document is an installation guide for a 15-inch wide undercounter/freestanding nugget ice machine. It provides comprehensive instructions for setting up, operating, and maintaining the appliance, ensuring safe and efficient use. The guide emphasizes important safety warnings, proper disposal of old refrigeration units, and detailed steps for installation, including water, drain, and electrical connections.
The ice machine is designed to produce nugget ice and can be installed as an undercounter unit or as a freestanding appliance. Its compact 15-inch width makes it suitable for various kitchen or bar setups where space might be limited. The unit is supplied without a finished door panel, offering flexibility for customization with either accessory door panels or custom panels made from wood or other materials. This allows the ice machine to seamlessly integrate with existing cabinetry and decor.
A key feature of this ice machine is its customizable door swing. The hinges can be configured to open from either the left or the right side, providing adaptability to different installation layouts and user preferences. The guide includes detailed instructions for changing the door swing, which should be performed before attaching any door panel. This flexibility ensures that the appliance can be optimally positioned in any space.
The ice machine requires a dedicated 115V, 60 Hz, 15 amp electrical supply, and it comes with a 6-foot, 3-wire cord. The guide strongly advises against removing the grounding pin from the cord's plug or using extension cords, highlighting the importance of proper electrical grounding to prevent fire or electrical shock hazards. If a Ground Fault Interrupter (GFI) is required by local codes, the guide specifies that it should be of the receptacle type, used with permanent wiring, on a dedicated circuit, and rated for Class A (5 mA +/- 1 mA trip current).
For water supply, the machine requires a 1/4-inch OD copper tubing inlet waterline, with a pressure range of 20 psi min. to 80 psi max., and water temperature between 50°F (10°C) min. to 100°F (38°C) max. An easily accessible shut-off valve should be installed between the supply and the unit, not behind the unit, for convenience and safety. The water connection is located at the back of the cabinet, utilizing a compression fitting, one of which is supplied with the unit. When built-in, sufficient tubing should be coiled behind the machine to allow it to be pushed into the cavity without kinking the tubing.
The ice machine offers two types of drain systems: a gravity drain model and an internal drain pump model. For the drain pump model, it includes 3/8-inch ID plastic drain tubing and a check valve, allowing the drain connection to be as high as 10 feet (3.05 m) above the ice machine. This is particularly useful for installations where a floor drain is not readily available. For the gravity drain model, the guide emphasizes the need for the tubing to be vented, free of kinks, and sloped towards the building drain, with air gaps typically required by local codes to prevent water backup into the ice storage bin. Detailed steps are provided for routing and connecting the drain tubing for both models.
Proper airflow is crucial for the ice machine's performance. The unit takes in room temperature air at the lower right front and expels warm air at the lower left front. Restricting this airflow can negatively impact the machine's ability to produce ice efficiently. Therefore, the installation guide stresses the importance of locating the unit so that its front is not blocked, ensuring adequate air circulation through the vents. The design allows the door to be flush with surrounding cabinetry, but not recessed, to maintain optimal airflow.
The installation process involves several steps, including attaching the door panel, which can be either an accessory panel or a custom-made panel. The guide provides precise measurements and instructions for creating and mounting a custom panel, ensuring it aligns correctly with the door and cabinet. It also details how to install hinge covers and the kickplate. The kickplate comes with a stainless steel covering, which can be removed to reveal a black finish, offering another customization option.
For maintenance and troubleshooting, the guide includes an installation checklist to verify that all steps have been completed correctly, from water and electrical connections to leveling and door panel installation. It also provides a section for service information, advising users to contact their dealer or an authorized service agency if issues arise. Users are encouraged to record the model and serial numbers, date of purchase, and dealer information for future reference, as these details are essential for obtaining service and ensuring warranty protection.
Safety is a paramount concern throughout the guide. Warnings about child entrapment and suffocation are prominently featured, urging users to remove doors and leave shelves in place when disposing of old refrigeration units. The guide also provides instructions for proper disposal, advising users to contact their municipal waste disposal authority. General safety precautions, such as reading all instructions, preventing children from operating the unit, and avoiding flammable fluids for cleaning, are clearly outlined to ensure safe operation and prevent hazards.
Overall, this installation guide is a comprehensive resource for anyone installing or maintaining the 15-inch wide undercounter/freestanding nugget ice machine. It covers all necessary aspects from initial setup to long-term care, with a strong emphasis on safety, customization, and optimal performance.
General| Weight | 125 lbs |
|---|---|
| Dimensions | 34" H x 15" W x 24" D |
| Power Supply | 115V / 60Hz |
| Electrical Requirements | 115V, 60Hz, 1Ph |
| Voltage | 115V |
