Vimar ELVOX 930G

Microfono
Microphone
Kikrofon
Micrófono
Microfone
Altoparlante
Loudspeaker
Haut-parleur
Lautsprecher
Altavoz
Altifalante
Volume interno
Internal volume
Volume intérieur
Lautstärke innen
Volumen interno
Volume interno
Volume esterno
External volume
Volume extérieur
Lautstärke außen
Volumen externo
Volume externo
Fig. 1
Fig. 2
Morsettiera
Terminal block
Boîte de raccordement
Klemmenleiste
Regleta conexiones
Bornes
Unità Sound System audio per 4+n - Sound System audio unit for 4+n
Unité Sound S. audio pour 4+n - Audio-Einheit Sound System f. 4+n
Unidades Sound System audio para 4+n - Unidade Sound System áudio para 4+n
Quando si utilizza il posto esterno 930G e si richieda di
aumentare notevolmente il volume è possibile allontanare il
microfono dall’altoparlante per evitare l’effetto LARSEN (fischio).
Per spostare il microfono eseguire quanto segue:
- Aprire lo sportello con la freccia dell’Art. 930G (Fig. 1)
- Sfilare il microfono dalla sue sede.
- Inserire il microfono nel lato destro della testata inferiore del
telaio serie 8000. Nella testata sono ricavate due lamelle dove
inserire il microfono (Fig. 2).
When the speech unit Art. 930G is used and the volume is to be
increased considerably it is possible to install the microphone far
away from the lousdspeaker to avoid the LARSEN effect (buzzing
sound). To displace the microphone operate as it follows:
- Open the door with the arrow of Art. 930G (Fig. 1)
- Remove the microphone from its seat.
- Insert the microphone on the right hand side of the frame (8000
Series) lower head. On the head there are two locks where to
insert the microphone (Fig. 2).
Lorqu’on utilise le poste externe Art. 930G et lorsqu’on
demande d’augmenter considérablement le volume il est
possible d’éloigner le microphone du haut-parleur pour éviter
l’effet LARSEN (bourdonnement). Pour déplacer le microphone
effectuer les opérations suivantes :
- Ouvrir la porte avec la flèche de l’Art. 930G (Fig. 1).
- Défiler le microphone de son siège.
- Insérer le microphone dans le côté droit de la tête inférieure du
châssis série 8000. Dans la tête il y a deux lamelles où insérer le
microphone (Fig. 2).
Wenn die Aussenstelle Art. 930G und das Lautstärke ist
beträchtlich zu verhöhen, kann das Microfon weit vern vom
Lausprecher eingebaut werden um den LARSEN Effekt (Pfeifen)
zu vermeiden.
- Die Tür mit den Pfeil des Arts. 930G öffnen (Fig. 1).
- Das Mikrofon aus seinem Sitz ausziehen
- Das Mikrofon auf die Rechtenseite des Untererkopfs des
Rahmens Baureihe 8000 einstecken. Es sind zwei Lamellen auf
dem Kopf um das Microfon einzustellen (Fig. 2).
Nos casos em que se utiliza o posto externo 930G e é necessário
aumentar o volume, é possível afastar o microfone do altifalante
para evitar o efeito LARSEN (ruído).
Para afastar o microfone proceder do seguinte modo:
- Abrir a tampa do Art. 930G (Fig. 1), de acordo com a seta.
- Retirar o microfone da sua sede.
- Inserir o microfone no lado direito do topo inferior do caixilho
série 8000. Neste topo existem duas tiras para aplicar o
microfone (Fig. 2).
Nos casos em que se utiliza o posto externo 930G e é necessário
aumentar o volume, é possível afastar o microfone do altifalante
para evitar o efeito LARSEN (ruído).
Para afastar o microfone proceder do seguinte modo:
- Abrir a tampa do Art. 930G (Fig. 1), de acordo com a seta.
- Retirar o microfone da sua sede.
- Inserir o microfone no lado direito do topo inferior do caixilho
série 8000. Neste topo existem duas tiras para aplicar o
microfone (Fig. 2).
Viale Vicenza, 14
36063 Marostica VI - Italy
www.vimar.com
930G
S6I.930.G00 05 1901

Vimar ELVOX 930G Specifications

General

Brand	Vimar
Model	ELVOX 930G
Category	Intercom System
Language	English

Summary

930 G Speech Unit Operation

Microphone Placement for Larsen Effect

Instructions for moving the microphone to prevent audio feedback (Larsen effect) by relocating it.

930 G System Wiring and Connections

External Panel and Component Wiring

Diagrams and terminal descriptions for connecting the 930G unit to external panels, locks, and buttons.

Internal Unit and Transformer Connections

Wiring details for internal intercom units and the required power transformer.

Conductor Size Requirements

Specifies the required conductor cross-sectional area for different circuit types in the installation.

Audio Noise Troubleshooting

Procedure to resolve audio buzzing by relocating the lock power supply wire from terminal 4 to AS.

930 G Integration with 875 GE Systems

Wiring for SingleDouble Residence Systems

Diagrams and terminal assignments for connecting the 930G unit with Art. 875G/E systems.

Optional Call Repeater Wiring

Instructions for installing and connecting an optional call repeater unit.

Conductor Specifications and Compliance

Guidance on conductor sizing and adherence to EMC directives for installation.

930 G Integration with 875 GS, 875 ES Systems

Wiring Diagrams for S Models

Schematics and terminal connections for 930G with Art. 875G/S and 875E/S external units.

Optional Call Repeater for S Systems

Guidance on connecting the optional call repeater for specific S model installations.

Conductor Specs and Regulations for S Models

Details on conductor cross-section and EMC compliance for S series systems.

930 G System Overview and Functionality

System Description

Details the 930G system's electronic signal and loudspeaker intercoms for audio door entry.

Principle of Operation

Explains the core functionality: visitor call initiation and internal user response.

User Operating Instructions

Guides the user on how to respond to a visitor's call and communicate.

General Information and Compliance

Instruction Manual Download

Details how to access and download the complete instruction manual from the VIMAR website.

Installation Requirements

Outlines that installation must be done by qualified personnel following country-specific regulations.

Regulatory Compliance

States the product's adherence to EMC directives and specific EN standards.

End-of-Life Equipment Disposal (WEEERAEE)

Guidance for users on the proper separate collection and disposal of the product at the end of its life.