VIPAR SPECTRA Timer Control TC1200 - User Manual

02
Setting system with Remote
For flowering stage: use all channels with 100% brightness.
This light includes IR (Infrared) LEDs which look dim/invisible, they are not faulty LEDs.
Two fans will work while VEG channel on, the rest two fans will work while BLOOM channel on.
The digital display will be turned off so it will not illuminates/emits blue light during light off-working time.
MODEL: TC1200
USER INSTRUCTIONS
Timer Control Series
www.viparspectra.com
Height (above plants' canopy)
Using Hours
Brightness (VEG/BLOOM)
10 on / 14 off 40 / 15
60 / 30
100 / 60
100 / 100
44" - 48"3-5 days acclimation period
Seedlings/ Young vegetative
Vegetative Stage
Flowering Stage
40" - 44"
32" - 40"
24" - 28"
12 on / 12 off
12 on / 12 off
18 on / 6 off
TC1200
IR8pcs look dim
Step 1. Remove the plastic separator from the battery.
Step 2. Press to turn on the light.
Step 3. Press to setup brightness for VEG channel. Using and , select the
desired brightness. Press to save settings.
Step 4. Press , repeat step 3 to setup brightness for BLOOM channel.
Step 5. Press to setup current time of day, the hour will flash. Using and ,
select the desired hour. Press or to save the hour and activate the minutes.
Using and , select the desired minutes. Press to save settings, or wait
about 3 seconds and the programmed time will be automatically saved.
OK
OK
VEG
BLOOM
CLOCK
Step 6. Press to setup light's start-working time, the hour will flash. Using and
, select the desired start-working hour. Press or to save the hour and
activate the minutes. Using and , select the desired minutes. Press to
save settings, or wait about 3 seconds and the programmed time will be automatically
saved.
Step 7. Press , repeat step 6 to setup light's off-working time.
Step 8. Press to confirm that the system has saved the desired start-working and
off-working time.
PREVIEW
ON
OFF
OK
Using Suggestions
PREVIEW
OK
VEG
BLOOM
ON
CLOCK
OFF
VIPARS PECTRA
To setup brightness for
BLOOM channel.
To setup light's start-working
time.
To setup light's off-working
time.
To setup brightness for
VEG channel.
To setup current time of day.
To turn ON/OFF the light.
To increase value.
Switch to other setting.
To decrease value.
Switch to other setting.
To save settings.
To preview start-working
and off-working time.
Note: Timer controls both channels on/off together. Cannot turn VEG and BLOOM channel
on/off separately.
Adjust the height and brightness accordingly to desired coverage and how well each individual
plants responds as the brightness increases. The key is to always observe your plants and listen
to what they're telling you. If the leaves are pointing hard towards the light, they love it! Give
them more! If they shy away or appear limp and unhappy, while all other components and
environmental variables are correct, back off with the light! They'll let you know very quickly how
they feel. This is of course... the key to horticulture in general.
The following section will help guide you in the process of evaluating the best methods
for each stage of plant growth. Like many other growers, you can use this light throughout
the seeding and flowering stages of your plants life. Remember to properly adjust the height
and brightness of your light according to your plants desired level for optimal growth.
Specifications:
Model:
LED Power:
Actual Power Draw:
LED Quantities:
Total Harmonic Distortion:
Input Voltage:
Frequency:
TC1200
1200W
110V: 530W±3%; 220V: 506W±3%
240pcs Epiled/Bridgelux LEDs
AC100-240V
50-60Hz
HID Replacement:
Vegetative Coverage at 32":
Flowering Coverage at 24":
Use for:
Housing Dimensions:
Item Weight:
Lifespan:
1000W HPS/MH
4.5x4.5ft
3.5x3.5ft
all stages grow and flowering
25.4 x 16.5 x 3 inches
64.5 x 42 x 7.5 cm
23 lbs
≥
100,000 hours
15%
<

Summary

Setting System with Remote

Remote Control Setup Steps

Step-by-step guide for configuring the timer using the remote control.

Product Specifications

Technical Specifications

Detailed technical specifications including model, power, coverage, and dimensions.

Usage Notes

Notes on IR LEDs, fan operation, and display behavior during use.

Using Suggestions

Growth Stage Recommendations

Recommended light height, hours, and brightness for plant growth stages.

Setting System with Control Knob

Digital Display Overview

Explanation of the main menus and sub-menus for the digital display.

Control Knob Setting Process

Step-by-step guide for setting the timer using the control knob.

Control Knob Actions

Summary of control knob actions and their corresponding functions.

Warranty Information

Warranty Terms and Conditions

Details on warranty period, coverage limitations, and customer service contact.

Overview

1. Function Description
2. Usage Features
3. Remote Control Usage
4. Control Knob Usage
5. General Usage Guidelines
6. Maintenance Features

The VIPARSPECTRA Timer Control Series, Model TC1200, is a sophisticated LED grow light system designed to provide optimal lighting conditions for plant growth across all stages, from seeding to flowering. This device offers both remote control and manual knob operation, providing flexibility and ease of use for growers.

Function Description

The TC1200 functions as a full-spectrum LED grow light, incorporating both visible light and Infrared (IR) LEDs. The IR LEDs may appear dim or invisible to the human eye but are crucial for plant development. The system is divided into two primary channels: VEG and BLOOM. The VEG channel is optimized for the vegetative growth stage, while the BLOOM channel is designed for the flowering stage. The light output of each channel can be independently adjusted for brightness, allowing growers to tailor the light spectrum and intensity to the specific needs of their plants at different growth phases.

A key feature of the TC1200 is its integrated timer control, which allows users to set specific ON and OFF times for the light. This ensures a consistent light cycle, essential for healthy plant development. The timer controls both VEG and BLOOM channels simultaneously; independent on/off control for each channel is not supported. The digital display, which turns off during light-off periods, prevents any unwanted light emission that could disrupt the plants' dark cycle.

The device also includes a preview function, enabling users to review their programmed start and off-working times before saving, ensuring accuracy in their lighting schedule.

Usage Features

The TC1200 offers two main methods of operation: a remote control and a control knob on the device itself.

Remote Control Usage:

1. Power ON/OFF: The remote has a dedicated button to turn the light ON or OFF.
2. Brightness Adjustment: Users can increase or decrease brightness using the '+' and '-' buttons.
3. Channel Selection: Separate buttons are provided to select and adjust the brightness of the VEG and BLOOM channels.
4. Time Setting:
   • Current Time: The 'CLOCK' button allows users to set the current time of day. The hour will flash, and '+' and '-' buttons are used to select the desired hour. Pressing 'OK' activates the minutes, which are then set using '+' and '-'. Pressing 'OK' again saves the settings.
   • Start-Working Time: The 'ON' button initiates the setting of the light's start-working time. Similar to setting the current time, the hour flashes, adjusted with '+' and '-', then 'OK' is pressed to activate minutes, which are also adjusted with '+' and '-'. Pressing 'OK' saves the settings.
   • Off-Working Time: The 'OFF' button is used to set the light's off-working time, following the same procedure as setting the start-working time.
5. Preview Settings: The 'PREVIEW' button allows users to confirm the saved start-working and off-working times.
6. Saving Settings: Settings are typically saved by pressing 'OK' or automatically after a few seconds of inactivity.

Control Knob Usage:

1. Power ON/OFF: Pressing the knob for approximately 3 seconds turns the light ON or OFF.
2. Navigation and Selection: The knob can be pressed to enter modes, change settings, or save settings.
3. Value Adjustment: Rotating the knob clockwise increases values, while rotating it counter-clockwise decreases values.
4. Brightness Adjustment (VEG/BLOOM):
   • From the main menu, select 'CH1' (VEG channel) or 'CH2' (BLOOM channel) by rotating the knob.
   • Press the knob to enter the brightness adjustment mode. The current brightness value will be displayed.
   • Rotate the knob to select the desired brightness (e.g., 50 for 50%).
   • Press the knob to save the desired brightness and proceed to the next step or menu.
5. Timer Setting (H-SE):
   • From the main menu, select 'H-SE' (Timer setting) by rotating the knob.
   • Press the knob to enter the timer setting menu.
   • Start-Working Time (00:00): Rotate the knob to select '00:00' (Start-working time). Press the knob. The hour will flash. Rotate the knob to select the desired hour. Press the knob to activate minutes. Rotate the knob to select the desired minutes. Press the knob to save.
   • Off-Working Time (OFF:A): Rotate the knob to select 'OFF:A' (Off-working time). Follow the same procedure as setting the start-working time.
   • Current Time (CLOC): Rotate the knob to select 'CLOC' (Current time). Follow the same procedure as setting the start-working time.
6. Automatic Saving: The system will save settings and return to the superior menu if no action is taken within 3-5 seconds.

General Usage Guidelines:

• Acclimation Period (3-5 days): For new plants, start with a lower brightness (e.g., 40/15 for VEG/BLOOM) and a 10 on / 14 off light cycle, with the light positioned 44"-48" above the canopy.
• Seedlings/Young Vegetative: Increase brightness slightly (e.g., 60/30) and maintain a 12 on / 12 off cycle, with the light 40"-44" above the canopy.
• Vegetative Stage: Further increase brightness (e.g., 100/60) and switch to an 18 on / 6 off cycle, with the light 32"-40" above the canopy.
• Flowering Stage: Maximize brightness (100/100) and use a 12 on / 12 off cycle, with the light 24"-28" above the canopy.
• Observation is Key: Always observe plant response. If leaves point strongly towards the light, they are thriving. If they appear limp or unhappy, reduce light intensity or increase the distance. This responsiveness is a critical indicator of plant health and light suitability.
• Airflow: Two fans operate when the VEG channel is on, and the remaining two fans operate when the BLOOM channel is on, ensuring adequate cooling for the system.

Maintenance Features

The VIPARSPECTRA TC1200 is designed for durability and longevity, with a specified lifespan of over 100,000 hours. While specific user-level maintenance instructions are not extensively detailed in the provided manual, general care practices are implied through the warranty terms and device design:

• Environmental Control: The warranty explicitly states that damage due to high moisture levels is not covered. This suggests that the device should be operated in a controlled environment with appropriate humidity levels to prevent internal damage and ensure optimal performance.
• Proper Installation: Improper hanging or mounting is also listed as a cause for warranty voidance, indicating the importance of secure and correct installation to prevent physical damage to the unit.
• Cleanliness: Dust build-up is mentioned as a factor that can void the warranty. This implies that regular cleaning of the device, particularly the cooling vents and LED surfaces, is necessary to maintain efficient operation and prevent overheating. Keeping the light free from dust ensures proper heat dissipation and maximizes light output.
• Power Management: The warranty also excludes damage from power surges, suggesting the use of surge protectors or stable power sources to protect the device's electronics.
• No User Modifications: Any user modifications to the device are not covered under warranty, indicating that the internal components are not user-serviceable beyond basic external cleaning.
• Battery Replacement (Remote): The remote control requires a plastic separator to be removed from the battery compartment before first use, implying that the remote's battery is user-replaceable when needed.

In summary, the VIPARSPECTRA TC1200 is a versatile and user-friendly LED grow light system offering precise control over lighting conditions for various plant growth stages. Its dual control methods, detailed timer functions, and emphasis on plant observation make it a valuable tool for both novice and experienced growers. Proper environmental conditions, installation, and occasional cleaning are essential for maintaining its performance and ensuring its long operational life.

VIPAR SPECTRA Timer Control TC1200 Specifications

General

Model	TC1200
Type	Timer Control
Voltage	120V
Max Load	15A
Programmable	Yes
Display	LCD
Compatibility	VIPARSPECTRA LED Grow Lights
Frequency	60Hz
Timer Modes	Daily, Weekly
Outlets	1
Timer Settings	Multiple programmable settings
Function	Automated on/off control