VITO VICSOS25 User Manual (English)

Questions and Answers:

A
Amy DuranAug 3, 2025
What to do if my VITO VICSOS25 Air Compressor stops and the overload relay trips?
- D
  David FischerAug 3, 2025
  If your VITO Air Compressor stops and the overload relay trips, it could be due to the motor overheating. Allow the compressor to cool down, then reset the overload relay and switch the compressor back on. Another cause might be blockage or damage to rotating parts, leading to motor overheating. In this case, remove or replace the faulty parts, press the overload relay trip button, and restart the compressor.
J
Juan PetersonAug 8, 2025
Why my VITO Air Compressor has low pressure?
- A
  Andrea HunterAug 8, 2025
  If your VITO Air Compressor runs but doesn't produce enough pressure or has a low discharge capacity, the air filter may be clogged. Try cleaning or replacing the air filter. There could also be a leak in the check and safety valve, so check and repair the valve. Another possibility is a leak in the discharge pipe, which you should also check and repair. Damaged seals can also cause this issue; replace them as needed. Ensure the tank drain plug is tightly screwed in, and inspect the screw’s joint, replacing it if necessary. Finally, the cylinder and segments might be damaged, requiring repair or replacement.
M
Monique WilliamsAug 14, 2025
How to troubleshoot VITO VICSOS25 that won't start?
- L
  Lori SheltonAug 14, 2025
  If your VITO Air Compressor motor doesn't start or turns slowly, first check the plug, socket, and circuit breaker of the power supply circuit to ensure there is supply voltage. If the supply voltage is too low, avoid using excessively long extension cords and use an extension cord with a sufficient transversal cross-section. Also, ensure that the ambient temperature is not too low; do not operate the compressor when outside temperatures are below +5°C. A failure in the pressure switch or the motor itself could also be the cause, requiring repair or replacement.
S
Sarah DavisAug 19, 2025
What to do if VITO Air Compressor pressure is ok but air tools don't work?
- N
  Nicole PattersonSep 12, 2025
  If your VITO Air Compressor is running, and the pressure gauge shows pressure, but your air tools aren't working, there might be a leak in the compressed air hose. Check the hose and tools, and replace them if necessary. Another potential cause is a leak in the quick-release coupling; inspect it and replace it if needed. Lastly, the pressure set in the pressure regulator might be too low. Try increasing the pressure in the air outlet pressure regulator.
D
Dr. Matthew CarterAug 23, 2025
Why does my VITO VICSOS25 Air Compressor start up regularly?
- S
  Sandra WallAug 23, 2025
  If your VITO Air Compressor starts up regularly due to pressure drops in the tank, even without any air tools connected or air flowing from the distribution network, it could be due to an air leak through the couplings. To identify the leak, let the compressor warm up until it reaches maximum pressure, then switch it off. If you can't hear any leaks, apply water mixed with detergent over all connections. The formation of air bubbles will reveal the leaks. Tighten the couplings where you see bubbles. If the issue continues, contact technical assistance.
M
Mary LopezAug 29, 2025
Why VITO VICSOS25 Air Compressor makes abnormal noise?
- A
  Alexa MartinezAug 29, 2025
  Abnormal noise or vibrations in your VITO Air Compressor can be caused by loose parts or connection accessories. Check all parts and retighten them. It could also be due to strange elements inside the motor, so check and clean the motor. If the moving parts are damaged, they will need to be repaired or replaced.