Vivotek FD9366-HV - Page 203

VIVOTEK
User's Manual - 203
© 2019 VIVOTEK INC. All Right Reserved
68
NAME VALUE SECURITY(
get/set)
DESCRIPTION
100: Best quality
* Only valid when
"mjpeg_ratecontrolmode"= vbr and
s<0~(m-1)>_mjpeg_quant = 100.
s<0~(m-1)>_mj
peg_maxvbrbit
rate
20000~"capability_videoin
_c<0~(n-1)>_mjpeg_maxbi
trate"
4/4 The maximum allowed bit rate in fixed
quality mode.
When the bit rate exceeds this value,
frames will be dropped to restrict the
bit rate.
* Only valid when
"mjpeg_ratecontrolmode"= vbr
s<0~(m-1)>_mj
peg_cbr_quant
1~5, 100 4/4 Set the pre-defined quality level:
1: Medium
2: Standard
3: Good
4: Detailed
5: Excellent
100: Use the quality level in
"cbr_qpercent"
* Only valid when
"mjpeg_ratecontrolmode"= cbr.
* Only available when
"capability_smartstream_version" >=
"2.0"
s<0~(m-1)>_mj
peg_cbr_qperc
ent
1~100 4/4 Select customized quality in a
normalized full range.
1: Worst quality
100: Best quality
* Only valid when
"mjpeg_ratecontrolmode"= cbr and
"quant"= 100.
* Only available when
"capability_smartstream_version" >=
"2.0"
s<0~(m-1)>_mj
peg_bitrate
20000~"capability_videoin
_c<0~(n-1)>_mjpeg_maxbi
4/4 The target bit rate in constant bit rate
mode.
© 2019 VIVOTEK INC. All Right Reserved
69
NAME VALUE SECURITY(
get/set)
DESCRIPTION
trate" * Only valid when
"mjpeg_ratecontrolmode"= cbr
s<0~(m-1)>_mj
peg_prioritypo
licy
framerate,imagequality 4/4 Set prioritypolicy
* Only valid when
"mjpeg_ratecontrolmode"= cbr
s<0~(m-1)>_mj
peg_maxframe
1~"capability_videoin_c<0
~(n-1)>_mjpeg_maxframer
ate"
1/4 The maximum frame rates of a mjpeg
stream at different
resolutions("capability_videoin_c<0~(
n-1)>_resolution") are recorded in
"capability_videoin_c<0~(n-1)>_mjpe
g_maxframerate"
s<0~(m-1)>_ra
tiocorrect
<boolean> 1/4 Change resolution to fit 4:3 ratio.
For PAL:
D1/4CIF(720/704x576) -> (768x576)
CIF(352x288)->(384x288)
For NTSC:
D1/4CIF(720/704x480) -> (640x480)
CIF(352x240)->(320x240)
* Only available when
capability_videoin_type is 0 or 1.
wdrpro_mode
<product
dependent>
<boolean> 4/4 Enable WDR pro
* Only available when
"capability_image_c<0~(n-1)>_wdrpro
_mode" > 0
wdrpro_streng
th
<product
dependent>
1~100 4/4 The strength of WDR Pro.
The bigger value means the stronger
strength of WDR Pro.
* Only available when
"capability_image_c<0~(n-1)>_wdrpro
_strength" is 1
wdrc_mode
<product
dependent>
<boolean> 4/4 Enable WDR enhanced.
* Only available when
"capability_image_c<0~(n-1)>_wdrc_
mode" is 1
wdrc_strength
<product
1~100 4/4 The strength of WDR enhanced.
The bigger value means the stronger