EasyManua.ls Logo

Volcano 20-200 - Maintenance and Troubleshooting; Burner Cleaning and Maintenance; Component Disassembly and Cleaning

Volcano 20-200
16 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
9
NOTE: Spiders and small insects can spin webs and build nests in-
side the burner. This especially occurs in late summer and fall before
frost when spiders are most active. These nests can obstruct gas ow
and cause a re in and around the burner and orice. Such a re can
cause operator injury and serious damage to the appliance. To help
prevent a blockage and ensure full heat output, clean and inspect
burner tube often (once or twice a month). NOTE: Water or air pres-
sure will not normally clear spider webs.
All cleaning and maintenance should only be done when the ap-
pliance is cool and with the fuel supply turned off at the LP cylin-
der. DO NOT clean any part in a self-cleaning oven. The extreme
heat will damage the nish.
CLEANING AND MAINTENANCE
Correct care and maintenance will keep your appliance operating
smoothly. Clean regularly as determined by the amount of use. NOTE:
Clean the entire appliance each ear and tighten all hardware on a
regular basis (1-2 times a year or more depending on usage). Clean-
ing should be done where detergents won’t harm patio, lawn, or the
like.
SUGGESTED CLEANING MATERIALS
• Mild dish washing liquid detergent
• Nylon cleaning pad
• Hot water
• Paper clip
• Soft brass bristled brush
COMPONENT CLEANING:
• After appliance has cooled, wipe areas where paint and nish have
burned off to minimize rusting. A vegetable based oil can be used to
“season” the interior of stove.
• COOKING SURFACES, POTS AND PANS: Clean the cooking sur-
face with soapy water and a nylon cleaning pad.
• Clean the wire rack with a wire brush and soapy warm water.
• BURNER: Wire brush loose corrosion from burner exterior. Clean
clogged gas port holes with an opened paper clip. Replace corroded
or damaged burners that would emit excess gas.
1. Remove orice/valve from burner.
2. Look inside the burner tube for nests, webs, or mud.
3. To remove the above obstructions, use an accessory ex-
ible venture brush or bend a small hook on one end of a
long exible wire or use an air hose.
4. Inspect and clean the burner if needed. Reattach orice/
hose to burner.
CAUTION
Cleaning The Burner
Steps for Cleaning The Burner
• Be sure the unit is cool.
• Always detach propane cylinder
outdoors away from ignition
sources.
• Unscrew the quick coupler from
the cylinder or detach 1 lb. cylinder
from propane valve adaptor. (Dis-
connect the 1 lb. cylinder when not
in use)
• Detach regulator hose assembly
from the propane burner.
• NOTE: Use hook to secure regula-
tor to the body when not in use.
• Remove the top grill.
• Remove the heat diffuser plate.
• Remove propane burner from the
bottom of the cooking chamber.
• Store top grill, bottom grate, and
diffuser plate inside inner pouch of
the Volcano storage bag.
• Clean top grill with warm water and
mild household cleaner.
• Do not use abrasives.
• Wipe the stove clean with soft cloth
and mild household cleaner.
• Clean the inside of the cooking
chamber with mild household
cleaner.
• Do not use abrasives.
• Wipe the cooking chamber clean
with soft cloth.
• Make sure the stove is completely
dry before storing.
Tear Down/Clean for Propane Fuel Source
Tear Down/Clean for Wood/Charcoal
• Make sure the unit is cool.
• Remove the top grill.
• Remove the bottom grate.
• Dump any remaining
debris or ash in a safe
location.