Vortex VO2811 User Manual

Fierăstrău electric cu lanț VO2811
10
Ulizare
Echipament de siguranță
Dispozivul este dotat cu mai multe echipamente
de siguranță care reduc riscul vătămării în mpul
ulizării:
Opritor de lanț
Opritorul de lanț are ca scop oprirea lanțului în
cazul în care acesta se rupe sau sare din lăcaș.
Aceste situații pot  prevenite prin întreținerea
cu regularitate a lamei de ghidaj și tensionarea
corectă a lanțului.
Protecția mâinii din spate
Protecția mâinii din spate are rolul de a proteja
mâna în cazul în care lanțul sare din loc și de
a împiedica ca crengile și nuielele rezultate
din acvitate să vă deranjeze în ulizarea
dispozivului.
Vericați înainte de a începe!
PERICOL!
Risc de vătămare!
Dispozivul trebuie ulizat doar dacă
nu au fost idencate defecțiuni.
În cazul în care a fost idencată
o defecțiune la vreo piesă, aceasta
trebuie schimbată înainte de
următoarea ulizare.
DANGER!
Risk of injury!
The device must only be put into
operation if no faults are found. If any
part of the device is defective, it must
be replaced before the next use.
Chain catcher
The chain catcher serves to catch a torn saw
chain or one which has jumped out of the
guide. Through regular maintenance of the
saw rail and correct and regular tensioning of
the saw chain, accidents of this type can be
prevented.
The rear hand guard
The rear hand guard serves to protect the
hand against a jumped chain and disturbing
branches and twigs.
Check before starting!
Check the safety equipment and the safe
condition of the device.
– Check all parts for their firm fit.
– Check whether there is any leakage.
– Check whether there are visible defects:
broken parts, cracks, etc.
– Check the device for correct chain ten-
sioning.
– Check the function of the chain brake.
Attaching the extension cable
► P.4 , item 7
– Plug the unit plug into the connector of
the extension cable.
– Feed the extension cable through the
strain relief mechanism (13) as shown.
Starting the device
► P. 4 , item 8
– Hold the device fast with both hands.
– The hand guard (8) must be folded
towards the back.
– Press the switch-on safety lock (11).
– Press the start button (12).
The device starts up.
Use
Before use, familiarize yourself sufficiently
with the sawing technique for chain saws.
You will find information about this in the
trade literature. We
recommend that you
attend suitable training sessions. The notes
here serve only as a complement!
Correct posture
– Stand with both legs securely on the
ground.
– Heed obstacles in the work area.
– While you are working, always hold the
device fast with both hands!
Hold the device:
– with the left hand on the handle.
– with the right hand on the handle.
– balanced in a secure position.
DANGER!
Risk of injury!
Never work on unstable subsurfaces!
Never work above shoulder height!
Never work while standing on a lad-
der!
Do not work bent too far forward!
Only use the device under favourable
weather and site conditions!
DANGER!
Risk of injury!
The device must only be put into
operation if no faults are found. If any
part of the device is defective, it must
be replaced before the next use.
Chain catcher
The chain catcher serves to catch a torn saw
chain or one which has jumped out of the
guide. Through regular maintenance of the
saw rail and correct and regular tensioning of
the saw chain, accidents of this type can be
prevented.
The rear hand guard
The rear hand guard serves to protect the
hand against a jumped chain and disturbing
branches and twigs.
Check before starting!
Check the safety equipment and the safe
condition of the device.
– Check all parts for their firm fit.
– Check whether there is any leakage.
– Check whether there are visible defects:
broken parts, cracks, etc.
– Check the device for correct chain ten-
sioning.
– Check the function of the chain brake.
Attaching the extension cable
► P.4 , item 7
– Plug the unit plug into the connector of
the extension cable.
– Feed the extension cable through the
strain relief mechanism (13) as shown.
Starting the device
► P. 4 , item 8
– Hold the device fast with both hands.
– The hand guard (8) must be folded
towards the back.
– Press the switch-on safety lock (11).
– Press the start button (12).
The device starts up.
Use
Before use, familiarize yourself sufficiently
with the sawing technique for chain saws.
You will find information about this in the
trade literature. We recommend that you
attend suitable training sessions. The notes
here serve only as a complement!
Correct posture
– Stand with both legs securely on the
ground.
– Heed obstacles in the work area.
– While you are working, always hold the
device fast with both hands!
Hold the device:
– with the left hand on the handle.
– with the right hand on the handle.
– balanced in a secure position.
DANGER!
Risk of injury!
Never work on unstable subsurfaces!
Never work above shoulder height!
Never work while standing on a lad-
der!
Do not work bent too far forward!
Only use the device under favourable
weather and site conditions!
Vericați echipamentele de siguranță și faptul că
dispozivul este într-o stare bună.
• Vericați dacă piesele sunt strânse cu fermitate.
• Vericați dacă există scurgeri.
• Vericați dacă există defecte vizibile: piese
rupte, crăpături etc.
• Vericați dacă lanțul este tensionat în mod
corect.
• Vericați funcționarea dispozivul de frânare a
lanțului.
Atașarea unui cablu prelungitor
• P. 4, arcolul 7
• Conectați ștecherul dispozivului în conectorul
cablului prelungitor.
• Introduceți cablul prelungitor prin mecanismul
de preluare a sarcinii cablului (13).
Pornirea dispozivului
• P. 4, arcolul 8
• Țineți mereu dispozivul în mod ferm, cu
ambele mâini.
• Protecția mâinii (8) trebuie să e îndreptată în
spate.
• Apăsați dispozivul de blocare a pornirii (11).
• Apăsați pe butonul de pornire (12). Dispozivul
va porni.
Ulizare
Înainte de a uliza dispozivul, familiarizați-vă
în mod adecvat cu tehnica de tăiere ulizând un
erăstrău cu lanț. Veți găsi informații relevante
în literatura de specialitate. Vă recomandăm
să parcipați la sesiuni adecvate de instruire.
Prevederile din acest manual trebuie să e
tratate doar ca o completare a cunoșnțelor
ulizatorului!
Postura corectă
Stați cu ambele picioare pe pământ.
• Aveți în vedere obstacolele prezente în spațiul
de lucru.
• În mp ce lucrați, țineți dispozivul ferm
folosind ambele mâini.
DANGER!
Risk of injury!
The device must only be put into
operation if no faults are found. If any
part of the device is defective, it must
be replaced before the next use.
Chain catcher
The chain catcher serves to catch a torn saw
chain or one which has jumped out of the
guide. Through regular maintenance of the
saw rail and correct and regular tensioning of
the saw chain, accidents of this type can be
prevented.
The rear hand guard
The rear hand guard serves to protect the
hand against a jumped chain and disturbing
branches and twigs.
Check before starting!
Check the safety equipment and the safe
condition of the device.
– Check all parts for their firm fit.
– Check whether there is any leakage.
– Check whether there are visible defects:
broken parts, cracks, etc.
– Check the device for correct chain ten-
sioning.
– Check the function of the chain brake.
Attaching the extension cable
► P.4 , item 7
– Plug the unit plug into the connector of
the extension cable.
– Feed the extension cable through the
strain relief mechanism (13) as shown.
Starting the device
► P. 4 , item 8
– Hold the device fast with both hands.
– The hand guard (8) must be folded
towards the back.
– Press the switch-on safety lock (11).
– Press the start button (12).
The device starts up.
Use
Before use, familiarize yourself sufficiently
with the sawing technique for chain saws.
You will find information about this in the
trade literature. We recommend that you
attend suitable training sessions. The notes
here serve only as a complement!
Correct posture
– Stand with both legs securely on the
ground.
– Heed obstacles in the work area.
– While you are working, always hold the
device fast with both hands!
Hold the device:
– with the left hand on the handle.
– with the right hand on the handle.
– balanced in a secure position.
DANGER!
Risk of injury!
Never work on unstable subsurfaces!
Never work above shoulder height!
Never work while standing on a lad-
der!
Do not work bent too far forward!
Only use the device under favourable
weather and site conditions!

Vortex VO2811 Specifications

General

Brand	Vortex
Model	VO2811
Category	Chainsaw
Language	English