EasyManuals Logo

Vortice VORT QUADRO MICRO 80 User Manual

Vortice VORT QUADRO MICRO 80
60 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #17 background imageLoading...
Page #17 background image
17
Do not use this appliance for purposes other than
those described in this booklet.
After removing the appliance from its packaging,
ensure that it is complete and undamaged. If in
doubt, contact a professionally qualified electrician
or Vortice*. Do not leave packaging within the
reach of children or infirm persons.
Certain basic rules must be observed when using
electrical appliances: a) Never touch electrical
appliances with wet or damp hands; b) Never touch
electrical appliances while barefoot; c) Do not allow
young children or infirm persons to use the
appliance without supervision; d) Supervise young
children to ensure that they do not play with the
appliance.
Store the appliance out of reach of children and
infirm persons after disconnecting it from the power
supply.
Do not operate the appliance where inflammable
vapours or substances are present (alcohol,
insecticides, petrol, etc.)
Take all necessary precautions to ensure that there
are no back flows of gas into the room from open-
flued combustion appliances.
If the product is installed at a height less than 2.3
metres, fit a protection grille over the air outlet to
prevent access to the fan impeller (fig. 39).
Do not make modifications of any kind to the appliance.
Do not expose the appliance to the weather (rain,
sun, etc.).
Periodically inspect the appliance for damage. If any
faults are found, do not operate the appliance;
contact Vortice* immediately.
In the event that the appliance malfunctions or
develops a fault, contact Vortice* immediately.
Ensure that only genuine original Vortice spares are
used for repairs.
In the event that the appliance is dropped or suffers a
heavy blow, have it checked immediately by Vortice*.
The appliance must be installed by a professionally
qualified electrician only.
Ensure that the electrical system to which the
appliance is connected complies with applicable
standards.
The appliance is double insulated and therefore
does not need to be earthed.
Check that the electrical power supply/socket provides
the maximum electrical power required by the
appliance. If this is not the case, arrange for a qualified
electrician to make the necessary modifications.
Use a multi-polar switch with minimum contact
gaps of 3 mm to install the appliance.
The TIMER or T HCS (Humidity Control
System) must be regulated by a qualified
technician.
Switch off the appliance at the main switch:
a) if the appliance does not function correctly;
b) before cleaning the outside of the appliance,
c) if the appliance is not to be used for any length of
time.
With the adjuster ring in place (fig. 7-A), the
appliance's outlet vent must be fitted to standard
ventilation hoses (nominal Ø 100 mm). If the
adjuster ring is not used (fig. 7-B), the vent can be
fitted to rigid red PVC piping (nominal Ø 100 mm).
Ensure that the room has an adequate source of fresh
air to ensure correct appliance operation. In the event
that other non-sealed combustion-based appliances
(such as water heater or gas stove) are installed in the
same room, check that air replacement is sufficient for
all appliances to work effectively together.
Do not use the appliance to control activation of
water heaters, room heaters, etc., nor should it
discharge into the hot air flues of such appliances.
Ensure that the appliance discharges into a single duct
(dedicated to this product) or directly to the outside.
The air to be extracted from the room must be clean
(i.e. free of grease, soot, chemical and corrosive
agents, explosive or flammable mixtures).
Keep the appliance's intake and outlet grilles free to
ensure an optimum flow of air.
The appliance is fitted with a PUR (polyurethan)
mesh filter. This can be cleaned by shaking, blowing,
or washing in water. Check the condition of the filter
and wash or replace it at least every 6 months of
operation (fig. 35-36).
N.B.
If the appliance is mounted on a wall which has
been tiled, a spacer is needed to eliminate any
misalignment and ensure correct functioning.
Warning: this symbol indicates precautions that must be taken to avoid injury
!
WARNING - CAUTION ENGLISH
Caution:
this symbol indicates precautions that must be taken to avoid damaging the appliance.
!
*or an authorized Vortice dealer if you are outside the UK-Ireland territory

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Vortice VORT QUADRO MICRO 80 and is the answer not in the manual?

Vortice VORT QUADRO MICRO 80 Specifications

General IconGeneral
BrandVortice
ModelVORT QUADRO MICRO 80
CategoryFan
LanguageEnglish

Related product manuals