VTech VM342-2 User Manual

Specifications are subject to change without notice.
© 2016 for VTech Communications, Inc. All rights reserved.
03/16. VM346-2_QSG_V1
Basic operation - Parent unit
"EKVTUTQFBLFSWPMVNF
Press     70-     to adjust your parent unit speaker
volume. It determines the volume of sound
transmitted from your baby units.
;PPN
Press to zoom in or out.
5BMLUPZPVSCBCZVOJU
Press and hold 5"-, and speak to your parent unit.
Your voice is transmitted to the baby unit.
5VSOPGGUIFTDSFFO
Press and hold -$%0/0'' to switch off the screen.
You can still hear sound from the selected baby unit.
6TFUIFNFOV
Press .&/64&-&$5 to enter the menu, choose
a menu item, or save a setting.
While in the menu:
Press
or to scroll up or down.
Press
to select an item, or save a setting.
Press
#"$, to return to the main menu or
idle screen.
•
•
•
5VSOPGGUIFQBSFOUVOJU
Press and hold to power off your parent unit.
Basic operation - Baby unit
Night vision
The baby unit has infrared LEDs that allow you to
see your baby at night or in a dark room. When the
baby unit detects low light levels, the infrared LEDs
turn on automatically. The images from this baby
unit is in black and white, and
appears on screen.
NOTES
It is norm al if you see a short w hite gla re on your pa rent
unit scr een as the baby unit i s adapti ng to the dark
environment.
When the i nfrare d LEDs are on, the image is in blac k
and whit e. This is normal du e to exter nal ligh t source s.
TIP
Depending on the surroundings and other interfering
factors, like lightings, objects, colors and backgrounds,
the display resolution may vary. Adjust the baby unit’s
angle, or place the baby unit at a higher level to prevent
glare and blurry display.
•
•
•
63
ē
ē
63
ē
63
ē
Alert Tone
Low Battery Tone
No Link Alert
Sound alert in split-view
Overview - Baby unit
Long press
"EKVTUTQFBLFSWPMVNF
Press      to adjust your baby unit speaker
volume. It determines the lullaby volume and
talkback volume transmitted from your parent unit.
5VSOPGGUIFCBCZVOJU
Slide the 0/0'' switch to 0'' to power
off your baby unit.
6U]KXOTMU
LL
6U
]KXOTMU
LL
2s
LCD is turning of
f...
2s
Sound activation
Automatically turns on the parent unit screen when the baby
unit being viewed detects a sound after the screen is turned
off. When no sound is detected within 50 seconds, the
screen is automatically turned of f to save power.
Sound-activated Screen
On
O
-VMMBCZ
Press / to play lullaby on the baby units.
Press
to skip to the other lullabies.
Press
/ again to stop the lullaby.
•
•
Overview - Parent unit
4UBOE
1PXFSKBDL
4QFBLFS
0OPGG
5"-,
;PPN
"OUFOOB
.JDSPQIPOF
-JHIUJOEJDBUPST
"SSPXLFZT
.&/6
   4&-&$5

   70-    
7*&8-$%0/0''
1"530-
41-*5
63
ē
*OGSBSFE-&%T
-JHIUTFOTPS
$BNFSB
0/0''-JHIU
Play/Stop
Microphone
4LJQ
Insert the screws into the
holes and tighten the screws
until only 1/4 inch of the
screws are exposed.
If you drill the holes into a stud,
go to step 3.
03
If you drill the holes into an object
other than a stud, insert the wall
anchors into the holes. Tap gently
on the ends with a hammer until
the wall anchors are flush with
the wall.
Mount the baby monitor (optional)
03
Place the wall mount bracket on a
wall and then use a pencil to mark
the top and the bottom holes as
shown. Remove the wall mount
bracket and drill two holes in the
wall (7/32 inch drill bit).
NOT
E
Check for reception strength and
camera angle before drilling the holes.
•
Align the wall mount bracket and
screws with the holes in the wall
as shown. Tighten the screw in the
middle hole first, so that the wall
mount bracket position is fixed. You
can tighten the other screw in the
top hole.
Place the baby unit on the wall
mount bracket. Tighten the screw
into the threaded socket at the
bottom to secure the baby unit.
The default angle of the wall mount bracket is 90 degrees. You
can maximize your baby unit’s viewing angles by tilting the wall
mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise
direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle.
Then, rotate the knob in clockwise direction to tighten the joint
and secure the angle.
Place the baby unit on the wall mount
bracket. Tighten the screw into the threaded
socket at the bottom to secure the baby
unit. Align the holes on the wall mount
bracket with the screws on the wall, and
slide the wall mount bracket down until it
locks into place.
4QFBLFS
0/0''TXJUDI



7PMVNFLFZT
5FNQFSBUVSF
TFOTPS

VTech VM342-2 Specifications

General

Brand	VTech
Model	VM342-2
Category	Baby Monitor
Language	English