VTech VM345 User Manual

VM345
VM345-15
VM345-19
Quick start guide
What’s in the box VM345 baby monitor system
Baby’s room Living room
Once you power on your baby monitor, your parent unit displays image from the baby unit, and the LINK LED light
turns on. The ON/OFF LED light of the baby unit also turns on.
Status check
63
ē
Dim mode
With dim mode preset to on, your parent unit display will dim after 10 minutes of inactivity to conserve energy.
10 min inactivity
Press any buttons
Night vision
The baby unit has infrared LEDs that allow you to
see your baby at night or in a dark room. When the
baby unit detects low light levels, the infrared LEDs
turn on automatically. The images from this baby
unit is in black and white, and appears on screen.
NOTES
It is normal if you see a short white glare on your parent
unit screen as the baby unit is adapting to the dark
environment.
When the infrared LEDs are on, the image is in black
and white. This is normal due to external light sources.
TIP
Depending on the surroundings and other interfering
factors, like lightings, objects, colors and backgrounds,
the display resolution may vary. Adjust the baby unit’s
angle, or place the baby unit at a higher level to prevent
glare and blurry display.
•
•
•
Connect and power on - Baby unit Install the battery
THIS SIDE UP
Connect and power on - Parent unit
CAUTION
The default volume of your parent unit
is level 4. If you experience high-pitched
screeching noise from your baby monitor
while positioning:
Make sure your baby unit and parent unit
are more than 1 meter (3 feet) apart, OR
Turn down the volume of your parent unit.
•
-
-
6U
]KXOTMUT
6U
]KXOTMUT
2s
> 1m (3ft)
> 1m (3ft)
< 1m (3ft)
6
3
6
3
Sound activation
Automatically turns on the parent unit screen when the baby
unit being viewed detects a sound after the screen is turned
off. When no sound is detected within 50 seconds, the
screen is automatically turned off to save power.
Sound-activated Screen
On
O
Go to www.vtechphones.com
to register your product for
enhanced warranty support
and latest VTech product news.

VTech VM345 Specifications

General

Type	Video Baby Monitor
Camera	Yes
Night Vision	Yes
Range	1000 feet
Two-Way Communication	Yes
Temperature Sensor	Yes
Zoom	Yes
Sound Activation	Yes
Battery Type (Parent Unit)	Rechargeable Lithium-Ion
Number of Cameras	1
Power Source	AC Adapter
Lullabies	5
Expandable	Up to 4 cameras

Summary

What's in the Box

Baby Unit Setup and Operation

Dim Mode

Parent unit display dims after 10 minutes of inactivity to conserve energy.

Sound Activation

Parent unit screen turns on when baby unit detects sound after screen is off.

Battery Installation

Parent Unit Setup and Operation

Volume and Noise Caution

Warning about high-pitched noise; keep units >1m apart or lower volume.

Status Check

Night Vision

Parent Unit Overview and Operation

Adjust Speaker Volume

Press +/VOL/- to adjust parent unit speaker volume which affects transmitted sound.

Talk to Your Baby Unit

Press and hold TALK, then speak to transmit your voice to the baby unit.

Turn Off Parent Unit Screen

Press and hold LCD ON/OFF to switch off the screen while sound continues.

Use the Menu

Press MENU/SELECT to enter, navigate, and select menu items or save settings.

Baby Unit Overview and Operation

Adjust Speaker Volume

Press ▼/VOL/▲ to adjust baby unit speaker volume for lullabies and talkback.

Lullaby Function

Press to play or skip lullabies on the baby unit; press again to stop.

Turn Off Baby Unit

Slide the ON/OFF switch to OFF to power off the baby unit.

Change Different Views

View Modes (Requires Additional Units)

Switch between baby units using VIEW, cycle through all with PATROL, or view simultaneously with SPLIT.

Mount the Baby Monitor (Optional)

Wall Mount Installation

Instructions for marking, drilling, inserting anchors, and securing the wall mount bracket.

Adjusting Viewing Angle

Tips for tilting the baby unit using the wall mount bracket for optimal viewing angles.