EasyManua.ls Logo

Vulcan-Hart A-130 - User Manual

Default Icon
17 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Vulcan
®
3-Series
Burnout Furnaces
Multi-Stage Programmable
Owner & Operator’s Manual
Models: 3-130 3-550 3-550A 3-550PD 3-1750 3-1750A
120V --- 9493308 --- 9493826 --- ---
100-120V 9493302 --- --- --- --- ---
230V --- --- 9493985 9493827 --- 9493990
200-240V 9493303 9493309 --- --- 9493409 ---
230V (EURO only) --- --- --- --- 9493658 9494064
Table of Contents
DESCRIPTION PAGE
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Control Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Delay Set-Up & Running a Delay Start Program Procedure: . .11
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Setup & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Product Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
English
CERAMCO
®

Other manuals for Vulcan-Hart A-130

Questions and Answers

  • H
    Heather LeAug 13, 2025
    How to troubleshoot a dead Vulcan-Hart A-130 Furnace?
    • K
      Kevin AndradeAug 13, 2025
      If your Vulcan-Hart Furnace is dead and not operating, here are a few things you can check: * Verify that the power receptacle or outlet has power. * Inspect the line or power cord connections. * Ensure the green power switch is turned on. * Examine the fuse (20 amp) and lamp on the control PDB.
  • J
    Jennifer LopezAug 16, 2025
    What to do if my Vulcan-Hart Furnace has no power or display?
    • K
      Kayla HebertAug 17, 2025
      If your Vulcan-Hart Furnace has no power or display, try the following: * Check the line or power cord connections to ensure they are secure. * Make sure the green power switch is turned on. * Inspect the fuse (20 amp) and the lamp on the control PDB.
  • J
    Jeremy DuarteAug 20, 2025
    Why is my Vulcan-Hart Furnace not heating during program?
    • M
      Ms. Stephanie HayesAug 20, 2025
      If your Vulcan-Hart Furnace is not heating during a program, consider these potential causes: * Ensure the door is completely closed, as the door switch may be interrupting power. * Check the heating element plates for continuity.
  • C
    Christopher LoweAug 25, 2025
    Why is my Vulcan-Hart A-130 heating too slow?
    • R
      Robert MolinaAug 25, 2025
      If your Vulcan-Hart Furnace is heating too slowly, here are a few possible reasons: * The heating rate may be programmed incorrectly (e.g., 1.5°/minute instead of 15.0°/minute). * Large loads can slow down response time, increasing the time to reach the desired temperature by 2 to 5 times. * The muffle may be nearing the end of its life.
  • L
    Louis McdonaldAug 28, 2025
    What to do if my Vulcan-Hart A-130 program turns off too early?
    • A
      andersoncandaceAug 28, 2025
      If the program on your Vulcan-Hart Furnace turns off too early, it might be due to these reasons: * A programmed rate set to zero will terminate the program. * The end-of-program option has been changed to option 3, which turns off the furnace at the end of the program.
  • M
    Mrs. Renee Sanders PhDSep 1, 2025
    How to fix a Vulcan-Hart A-130 power door that does not open?
    • M
      mpowellSep 1, 2025
      If the power door on your Vulcan-Hart Furnace does not open, consider the following: * There is a hidden switch located between the °C/°F key and the Delay (3-550PD only) Start key that activates the door. Try pressing it to test the operation. * Check the activation switch connections to the back of the furnace. * Allow the furnace to cool, then activate the switch and manually assist the door by lifting or pushing it in the appropriate direction.
  • S
    Sonia JordanSep 4, 2025
    How to adjust a loose or tight door on a Vulcan-Hart A-130?
    • A
      Amy Garcia MDSep 5, 2025
      If the door on your Vulcan-Hart Furnace is too loose or too tight, you can adjust the force or drag on the door movement by adjusting the hex screws. These are located on the upper rear corners of the furnace cabinet. Make sure to adjust both sides equally. Turning the screw clockwise adds drag and requires more force to move the door.
  • T
    Todd AtkinsonSep 8, 2025
    Why does the fan not operate in my Vulcan-Hart A-130 Furnace?
    • D
      Dr. Zachary PerezSep 8, 2025
      The fan in your Vulcan-Hart Furnace (Air Exchange Model Only) operates only during a start cycle. A setting of 0 means the fan is not active.

Vulcan-Hart A-130 Specifications

General IconGeneral
BrandVulcan-Hart
ModelA-130
CategoryFurnace
LanguageEnglish

Related product manuals