EasyManua.ls Logo

Wacker Neuson BS 60-2 - User Manual

Wacker Neuson BS 60-2
50 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operator’s Manual
Rammer
BS 60-2
BS 70-2
5000184135 06 0411
5000184135
EN

Table of Contents

Other manuals for Wacker Neuson BS 60-2

Preview: Repair Manual
Repair Manual156 pages

Questions and Answers

  • P
    pthomasSep 3, 2025
    Why Wacker Neuson Vibratory rammer & tamper overheats?
    • S
      Sharon CainSep 3, 2025
      If your Wacker Neuson vibratory rammer & tamper engine is overheating, it could be due to not enough oil in the fuel mix, which requires draining the tank and refilling it with new mixed fuel. Alternatively, the carburetor fuel mix may be set too lean, requiring a reset of the carburetor adjustments. Another potential cause is cooling fins or fan blades packed with dirt, which means you'll need to clean the debris from the fins and blades.
  • W
    wooddonnaSep 1, 2025
    Why Wacker Neuson Vibratory rammer & tamper engine does not accelerate?
    • J
      Joyce OlsonSep 2, 2025
      If your Wacker Neuson vibratory rammer & tamper engine isn't accelerating properly or is running poorly, consider these potential causes: dirty air filters (clean or replace them), too much oil in the fuel (drain the tank and refill with new mixed fuel), a fouled or incorrect spark plug (clean, replace, and ensure it's a resistor-type), a dirty muffler or exhaust port (clean them), an incorrect fuel mixture adjustment (adjust the screw and clean the fuel jets), or an air leak in the carburetor system (check all connections). For leaking crankshaft seals, consult the WM 80, WM 90, or Yanmar Engine Repair Manual.
  • Z
    zschmittAug 31, 2025
    What to do if Wacker Neuson Vibratory rammer & tamper engine does not start?
    • S
      Sarah GonzalezAug 31, 2025
      If your Wacker Neuson vibratory rammer & tamper engine won't start, begin by checking if there's fuel in the tank and ensuring the fuel valve is open. A fouled spark plug could also be the culprit; try cleaning or replacing it and setting the electrode gap. Other potential issues include a plugged fuel filter (replace it and inspect the fuel lines), an incorrect fuel mixture adjustment (adjust the screw and clean the fuel jets), a failed ignition module (replace it), or, on machines with oil injection, a failed float switch (replace it).
  • R
    Rhonda SpenceAug 29, 2025
    Why Wacker Neuson Vibratory rammer & tamper engine hard to start?
    • K
      Kristina BaileyAug 29, 2025
      If your Wacker Neuson vibratory rammer & tamper engine is hard to start, several factors could be the cause. It could be due to dirty air filters, which require cleaning or replacement. Another cause might be too much oil in the fuel, necessitating draining the old fuel and replacing it with a fresh mixture. Fouled or incorrect spark plugs, a dirty muffler or exhaust port, an incorrect fuel mixture adjustment, or low engine compression can also prevent the engine from starting easily. In the case of leaking crankshaft seals or low engine compression, consult the WM 80 Engine Repair Manual or the WM 80, WM 90 or Yanmar Engine Repair Manual respectively.
  • A
    Angel ConnerAug 27, 2025
    What to do if Wacker Neuson Power Tool engine runs but the rammer does not tamp?
    • N
      nbriggsAug 27, 2025
      If the engine of your Wacker Neuson Power Tool runs but the rammer doesn't tamp, inspect the clutch for damage and replace it if necessary. Also, consider replacing a broken connecting rod or crankgear. Further, check for low engine performance, check for compression loss, or clear a plugged exhaust port.
  • T
    Theresa KochAug 26, 2025
    Why is the Wacker Neuson Power Tool rammer operation erratic?
    • M
      madison19Aug 26, 2025
      If the rammer operation of your Wacker Neuson Power Tool is erratic, it could be due to oil or grease on the clutch, so clean the clutch. Alternatively, you might need to replace broken or worn springs, remove soil buildup on the ramming shoe, replace broken parts in the ramming system or crankcase, or reduce engine operating speed.
  • J
    Joseph RomeroAug 25, 2025
    What to do if Wacker Neuson Power Tool engine overheats?
    • M
      mphillipsAug 25, 2025
      If your Wacker Neuson Power Tool engine is overheating, it could be due to an improper fuel mix, so adjust the fuel mix. It may also be caused by not enough oil, so add oil. Another possible reason is that you need to clean the cooling fins and fan blades.
  • C
    Christine SpencerAug 22, 2025
    What to do if my Wacker Neuson Power Tool engine does not start or stalls?
    • J
      jennifer55Aug 22, 2025
      If your Wacker Neuson Power Tool engine fails to start or stalls, there are a couple of potential causes. First, check if there is fuel in the tank and fill it if necessary. Also, the spark plug may be fouled, in which case you should clean or replace it.

Summary

Safety Information

Signal Word Definitions

Explains DANGER, WARNING, CAUTION, NOTICE signal words and the safety alert symbol.

Machine Description and Intended Use

Safety Guidelines for Operating the Machine

Operator Safety with Internal Combustion Engines

Service Safety Precautions

Label Meanings

Lifting and Transporting

Safe Lifting and Transport

Provides instructions and safety precautions for lifting and transporting the machine.

Operation

First-Time Machine Preparation

Details the steps to prepare the machine for its initial operation.

Recommended Fuel Mixture

Operator Positioning

Before Starting

Starting Procedures

Stopping Procedures

Emergency Shutdown Procedure

Maintenance

Emission Control System Maintenance

Periodic Maintenance Schedule

Air Cleaner Servicing

Ramming System Oil Service

Shoe Hardware Maintenance

Idle Speed Adjustment

Basic Troubleshooting

Technical Data

Rammer Specifications

Wacker Neuson BS 60-2 Specifications

General IconGeneral
BrandWacker Neuson
ModelBS 60-2
CategoryVibratory rammers & tampers
LanguageEnglish

Related product manuals