To Next PageTo Next PageHow do I troubleshoot 'Error 10' on my Waeco AirConServiceCenter ASC 1300 G Air Conditioner?
If the Waeco Air Conditioner displays “Error 10”, it means that during the software test, the compressor failed to reduce the internal pressure sufficiently. Check for residual pressure on the pressure gauges, verify the pressure transducer calibration, check the internal bottle pressure, and inspect the compressor and corresponding solenoid valves.
Why does my Waeco Air Conditioner display 'Not enough vacuum! Carry on?'?
If the Waeco Air Conditioner displays “Not enough vacuum! Carry on?”, it means that during the vacuum process, the pressure in the air conditioning system is still more than 50 mbar after 8 minutes. Check the air conditioning system and its connections to the AirCon Service Center for any leaks.
What to do if Waeco AirConServiceCenter ASC 1300 G displays 'A/C system leakage! Carry on?'?
If the Waeco Air Conditioner displays “A/C system leakage! Carry on?”, it means that at the end of the vacuum process, the air conditioning system shows a vacuum loss of more than 120 mbar during the checking time. Inspect the air conditioning system and the connections between it and the AirCon Service Center for leaks.
What does 'Warning! Internal vessel full!' mean on my Waeco AirConServiceCenter ASC 1300 G?
If the Waeco Air Conditioner displays “Warning! Internal vessel full!”, it indicates that the internal refrigerant container is too full to hold the quantity to be extracted. You should drain the internal refrigerant container properly.
How to fix 'Error 01' on Waeco AirConServiceCenter ASC 1300 G Air Conditioner?
If the Waeco Air Conditioner displays “Error 01” or “Error 02”, it indicates that it was not possible to reduce the pressure sufficiently before or during the pressure increase test. Check the air conditioner and connections for leaks, constrictions, and ice build-up. Also, verify the pressure transducer calibration.
What does 'Warning! Not enough vacuum for injection!' mean on my Waeco AirConServiceCenter ASC 1300 G?
If the Waeco Air Conditioner displays “Warning! Not enough vacuum for injection!”, it means that during the filling phase, the vacuum in the air conditioning system is insufficient to end the process. Check the air conditioning system or the connections between it and the AirCon Service Center for leaks.
How to troubleshoot 'Error 12' on Waeco Air Conditioner?
If the Waeco Air Conditioner displays “Error 12”, it means that it was not possible to remove any refrigerant from the internal tank during the software test. Check pressure transducer calibration. Check whether the tank valve on the internal tank is open. Check the RE valve. Is the ambient temperature below 10 °C?
What does 'Error 03' mean on my Waeco AirConServiceCenter ASC 1300 G Air Conditioner?
If the Waeco Air Conditioner displays “Error 03”, it means that no data is coming from the refrigerant scale. Check the scale.
What does 'External tank empty or closed valve. Check!' mean on Waeco Air Conditioner?
If the Waeco Air Conditioner displays “External tank empty or closed valve. Check!”, it means that at the start or during the filling of the internal refrigerant container, the set refrigerant quantity cannot be attained. Check if the external refrigerant container has enough refrigerant or if the valves of the external refrigerant container are open.
What to do if Waeco AirConServiceCenter ASC 1300 G displays 'Not enough oil. Add!'?
If the Waeco Air Conditioner displays “Not enough oil. Add!”, it means that during the filling process, there is not enough fresh oil in the container to finish the process. Top up the fresh oil container with a suitable oil type.
General| Brand | Waeco |
|---|---|
| Model | AirConServiceCenter ASC 1300 G |
| Category | Air Conditioner |
| Language | English |
Contact information for additional support and information regarding the AirCon Service Center.
Defines warning, caution, notice, and note symbols used throughout the operating manual.
Outlines essential safety guidelines and precautions for operating the AirCon Service Center.
Provides critical information on safe usage, maintenance, and handling of the AirCon Service Center.
Details safety measures and precautions when working with refrigerants.
Covers operational procedures and personnel training requirements for safe unit usage.
Highlights specific warnings and precautions related to the AirCon Service Center's operation.
Explains the function of built-in safety mechanisms like pressure monitors and relief valves.
Lists the components and accessories provided with the AirCon Service Center.
Details optional accessories that can be purchased separately for the AirCon Service Center.
Identifies and describes the components and controls on the front of the unit.
Illustrates and describes the rear and side panels of the AirCon Service Center models.
Step-by-step guide for physically setting up and powering on the AirCon Service Center.
Describes the information displayed in the standby mode of the unit.
Instructions for changing the display language of the AirCon Service Center.
Procedure for inputting company specific information for service logs.
How to set the current date and time for accurate service log entries.
Guidance on modifying preset operational parameters and default settings.
Instructions for correctly installing oil and UV additive containers into the unit.
How to specify the volume of oil and UV additive containers for accurate measurement.
Procedure for initial filling of the unit's internal refrigerant storage.
Steps for safely shutting down the unit for repairs or in emergencies.
Initiates a fully automatic service sequence with minimal user input.
Manages user access and security codes for the system.
How to create a database of vehicles with their specific refrigerant filling quantities.
Storing and retrieving operational data via USB for reporting and analysis.
How to view refrigerant usage data (filled and extracted) on the unit's display.
Performing tests on the vehicle's AC system, with or without refrigerant.
Allows step-by-step execution of service processes, with options to omit or customize.
Procedure for flushing the vehicle's AC system with refrigerant.
Annual procedure to check the unit for refrigerant leaks.
Ensures accurate measurement of oil and UV additive quantities by resetting scales.
Instructions for replacing the unit's dryer filter.
Details on maintaining the filter and resetting related service messages.
Procedure to ensure accurate pressure measurements by calibrating the transducer.
Steps for safely draining and refilling the vacuum pump oil.
Accessing and understanding various internal counters and readings.
Adjusting fill quantities to compensate for different service hose lengths.
Guide for replacing the thermal printer paper roll.
Process for updating the unit's firmware and database using a USB drive.
Procedure for safely releasing non-condensing gases from the internal tank.
A comprehensive list of common error messages and their corresponding solutions.
Technical specifications, dimensions, and performance data for each model.
Schematic diagrams illustrating the refrigerant flow for different models.
Electrical schematics for the ASC 1300 G, ASC 2300 G, and ASC 3300 G models.
