WAGNER Paint Crew - User Manual

20 pages

Save Page as PDF

To Next Page

English

Printed in China

HIGH PERFORMANCE AIRLESS SPRAYER

TABLE OF CONTENTS:

SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

BEFORE YOU BEGIN SPRAYING . . . . . . . . . . . . . . . . . . . . . 5

PURGING AND PRIMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

SPRAYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SPRAYING TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . 8

CLEANUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10

INLET/OUTLET VALVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-38

SERVICE CENTER LIST . . . . . . . . . . . . . . . . . . . . . . . . . 39-43

WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

OWNER’S MANUAL • READ THIS MANUAL FOR COMPLETE INSTRUCTIONS

0805 • Form No. 0515801G

SPECIFICATIONS:

Weight .............................. 25 lbs.

Capacity ........................... 2 gallon hopper

Power source ...................3/8 Hp universal motor

Power requirement ...........15 amp minimum circuit on 120 VAC,

60 Hz current

Generator .........................8000 W

Spraying pressure

............

2800 PSI

Safety features .................Spray gun trigger lock and guard;

built-in tip safety guard; priming

knob for safe pressure release.

Conforms to UL STD 1450.

Certified to CAN/CSA C 22.2

NO 68-92.

Capability

..........................Sprays a variety of paints, oil

base, latex, primers, stains,

preservatives and other

nonabrasive materials.

Do not use materials with flash

points below 70°F (21°C).

1-800-328-8251

Wagner Technical Service

Need help?

Call us first for answers fast.

Call Wagner Spray Tec h toll-free if you have any

comments or problems with this product.

1770 Fernbrook Lane, Minneapolis, MN 55447

http://www.wagnerspraytech.com

Visit us on the world wide web!

This pump should not be used with textured materials,

block filler, lacquers, industrial enamels, or asphalt

sealer or materials containing HHC. See coating

supplier if flash point is not listed on the container.

Main Page

Questions and Answers

C
cesarbakerJul 26, 2025
How to unclog WAGNER Paint Crew tip?
- M
  Michael PowersJul 26, 2025
  If your WAGNER Paint Sprayer tip is clogged, here's what to do: First, turn off the pump, release the trigger, and lock the gun. Rotate the reversible tip arrow 180° to the CLEAN position (arrow pointing towards the rear of the gun). If the tip is hard to turn, switch the PRIME/SPRAY knob to PRIME and trigger the gun to relieve pressure. Then, switch back to SPRAY. Unlock the gun, aim at scrap material, and squeeze the trigger to blow out the obstruction. Once clean, paint will spray in a high-pressure stream. If it's still clogged, repeat these steps. Finally, return the tip to the SPRAY position (arrow pointing forward) and continue spraying.
M
Marissa LeeAug 9, 2025
What to do if WAGNER Paint Crew Paint Sprayer gun filter is clogged?
- M
  Michael RobertsAug 10, 2025
  If your WAGNER Paint Sprayer's gun filter is clogged, unclip the trigger guard from the filter housing. Unscrew the housing and remove the filter. Clean the filter with the appropriate cleaning solution: warm, soapy water for latex paints or mineral spirits for oil-based materials. Check for sediments in your spraying material and inspect the filter for holes, replacing it if necessary. Reinstall the cleaned filter into the gun housing, tapered end first.