Watanbe A5000 Series - Parameter Setup and Data; Navigating Parameter Setup Mode; Parameter Lists and Default Settings

5.2 Moving to the Parameter Setup Mode
5.3 Data Lists and Default Settings
Instruction Manual for A5000 Series 5/12
Conditiondata Comparatordata Scalingdata Linearizationdata
Measurement
PressingtheENTERkeysavesthedataandreturnstothemeasurementmode.
Calibrationdata
Shiftdata
(DataarebackedupwithEEPROMevenwhenthepoweristurnedoff.)
Default Equipped
Indication Name value as 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 0 1 2 3 4 5 6 7
PVH Peakholdsetup PH ○
RANG Measurementrangesetup *1 × ○ ○ ○ ○ ○ ○ ○ × ○ × ○ ○ ○ ○ ○ × ○
11 15 25 13 15 13 15 25 26 25 26 14 B JPB 14 14 2A
AVG Numberofaveraging 1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ × × ○ ○
MAV Numberofmovingaveragingsetup OFF ○
S.UD Stepwidesetup 1 ○
BLNK Indicationblanksetup OFF ○
UNIT Unitsetup C × × × × × × × × × × × × ○ ○ × × × ×
BAUD Baudratesetup 9600 × × × ○ ○ × ○ ○
DATA Datalengthsetup 7 × × × ○ ○ × ○ ○
P.BIT Paritybitsetup E × × × ○ ○ × ○ ○
S.BIT Stopbitsetup 2 × × × ○ ○ × ○ ○
T- Delimitersetup CR.LF × × × ○ ○ × ○ ○
ADR EquipmentIDsetup 00 × × × × ○ × × ○
A.OUT Analogoutputsetup OFF × × ○ × × ○ ○ ○
B.UP Digitalzerobackupsetup OFF ○
LINE Linearizationsetup CLR ○
I.SEL Inputselection OC × × × × × × × × × × × × × × ○ × × ×
TRT Trackingzeroingtimesetup 00
○
× ×
TRV Trackingzeroingwidthsetup*2 01
○
× ×
SNSR Sensorpowersetup 5 × × × × × × × × × × × × × × × × ○ ×
PＯＮ Power-ondelaysetup OFF ○
PRO Protectsetup OFF ○
U-NO. UnitnumberIndicationsetup ON ○
S-HI HIsidejudgmentvaluesetup 1000 × ○ × × × ○ ○ ○
S-LO LOsidejudgmentvaluesetup 500 × ○ × × × ○ ○ ○
H-HI HIsidehysteresissetup 0 × ○ × × × ○ ○ ○
H-LO LOsidehysteresissetup 0 × ○ × × × ○ ○ ○
FSC FullscaleIndicationvaluesetup *1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ × × × × × ○
9999 9999 9999 9999 9999 9999 9999 9999 9999 9999 9999 9999 9999
FIN Fullscaleinputvaluesetup *1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ × × × × × ○
9999 9999 9999 9999 9999 9999 9999 9999 5000 9999 5000 9999 *3
OFS Offsetindicationvaluesetup *1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ × × × × × ○
0 0 0 0 0 0 0 0 0 0 0 0 0
OIN Offsetinputvaluesetup *1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ × × × × × ○
0 0 0 0 0 0 0 0 0 0 0 0 *4
PS Pre-scalingvaluesetup 1 × × × × × × × × × × × × × × ○ ○ × ×
PPR Frequencydivisionsetup 1 × × × × × × × × × × × × × × ○ ○ × ×
DLHI DigitallimiterHIvaluesetup 9999 × × × × × × × ×
DLLO DigitallimiterLOvaluesetup -9999 × × × × × × × ×
AOHI AnalogoutputHIindicationsetup 9999 × × ○ × × ○ ○ ○
AOLO AnalogoutputLOindicationsetup 0 × × ○ × × ○ ○ ○
DEP Decimalpointpositionsetup None ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ × × ○ ○ ○ ○
*5 ○
ZERO Zeroinputvalue*6 0 × × × × × × × × × × × × × × × × ○ ×
SPIN Spaninputvalue*6 2000 × × × × × × × × × × × × × × × × ○ ×
SPAN Spanindication 9000 × × × × × × × × × × × × × × × × ○ ×
SHF Shiftdatasetup 0 ○
*1 Eachvalueinthelowerpartofacellinthecolumnsontherightisthedefaultvalue.
*2 TrackingzerowidthsetupparameterisnotindicatedifthetrackingtimeissettoOFF(0).
*3 5000for1Vrangeand2000for2Arange
*4 1000for1Vrangeand400for2Arange
*5 Linearizationdataarenotsetupforthedefaultvalues.
*6 Thisvalueisnotindicatedifcalibrationisdoneusinganactualload.
Theshadedpartsshowtheparametersthatmustbesetforeachunit.
Shiftdata
Inputunitnumber Outputunitnumber
Linearizationdata
Calibrationdata
Conditiondata
Comparatordata
Scalingdata
○
○
○
○
○
○
○
○
× × × × × × × × × × ×
× × × × × × × × × × ×