Waterway Power Defender 140

Questions and Answers

C
Christina DennisAug 19, 2025
What to do if my Waterway Swimming Pool Pump motor stalls during operation?
- P
  Paul StephensAug 19, 2025
  If your Waterway Swimming Pool Pump motor stalls during operation, it could be due to an overloaded motor. Disconnect the electrical power and check if the pump rotates freely. Another cause might be low voltage; in that case, verify that the motor voltage under load at the conduit box connection terminals matches the nameplate voltage requirements. A breaker trip could also be the reason. If this is the case, a qualified electrician should ensure the breaker's rating is properly sized to the motor's current rating, according to the National Electrical Code.
H
Heather CarpenterAug 21, 2025
How to troubleshoot a Waterway Swimming Pool Pump motor that fails to start?
- K
  Kaitlyn MillerAug 21, 2025
  If your Waterway Swimming Pool Pump motor fails to start, first verify that the motor voltage to the terminals matches the nameplate voltage requirements and choose the correct voltage position on the Voltage Selection Switch. Also, turn OFF the power and check the terminal connections according to the terminal connection section of this manual.
S
Shannon SandovalAug 23, 2025
Why is my Waterway Power Defender 140 motor vibrating or excessively noisy?
- B
  Brandon WellsAug 23, 2025
  If your Waterway Swimming Pool Pump motor vibrates or is excessively noisy, first ensure the electrical power is OFF. Check that the pump is properly connected to the motor shaft and inspect the pump impeller for damage. Also, make sure there are no foreign objects inside the pump. If applicable, verify that the motor base is not cracked and that the four mounting bolts are tightened securely.
A
Amanda BuckAug 26, 2025
What does error E 16 mean on my Waterway Power Defender 140?
- J
  Jordan ThompsonAug 26, 2025
  If the Waterway Swimming Pool Pump displays the error code E 16 – Motor Stalled, it could be due to an accumulation of dirt or debris in or around the motor causing the impeller to jam. Press the Start/Pause button to clear the fault from the LCD display and restart the motor by pressing any Speed button. If the fault continues to occur after a maintenance inspection, contact your pool professional or a qualified electrician for service.
T
Troy ForbesAug 27, 2025
What does error E0 mean on my Waterway Power Defender 140?
- C
  charlotte99Aug 28, 2025
  If the Waterway Swimming Pool Pump displays the error code E 0 – Overcurrent (HW), press the Start/Pause button to clear the fault from the LCD display. Then, press any Speed button to restart the motor. If the fault continues to occur, contact your pool professional or a qualified electrician for service.
D
Derrick PriceAug 30, 2025
Why my Waterway Power Defender 140 motor does not come up to full speed?
- F
  francesmanningAug 30, 2025
  If your Waterway Swimming Pool Pump motor does not come up to full speed, verify that the motor voltage under load to the terminals matches the nameplate voltage requirements.
A
Alicia GilesSep 1, 2025
What does error E5 mean on my Waterway Swimming Pool Pump?
- R
  rachel24Sep 1, 2025
  If the Waterway Swimming Pool Pump displays the error code E 5 – Open Phase, press the Start/Pause button to clear the fault from the LCD display and restart the motor by pressing any Speed button. If the fault continues to occur after verifying the wire connections, contact your pool professional or a qualified electrician for service.
S
Sue RobertsSep 3, 2025
What does error E8 mean on my Waterway Swimming Pool Pump?
- J
  jason93Sep 3, 2025
  If the Waterway Swimming Pool Pump displays the error code E 8 – MC EE Error, press the Start/Pause button to clear the fault from the LCD display and restart the motor by pressing any Speed button. If the fault continues to occur after verifying the wire connections, contact your pool professional or a qualified electrician for service.
K
Kevin SuarezSep 5, 2025
What does error E1 mean on my Waterway Power Defender 140 Swimming Pool Pump?
- R
  Rebecca PenningtonSep 5, 2025
  If the Waterway Swimming Pool Pump displays the error code E 1 – Low Voltage, the fault automatically clears and the motor restarts when the input voltage returns to a normal state. If the fault continues to occur after verifying input line voltage is correct, contact your pool professional or a qualified electrician for service.
C
Cynthia MeyerSep 7, 2025
What does error E11 mean on my Waterway Swimming Pool Pump?
- S
  Shari BrownSep 7, 2025
  If the Waterway Swimming Pool Pump displays the error code E 11 – MC Comm Lost, press any Speed button to restart the motor. If the fault continues to occur after verifying the wire connections, contact your pool professional or a qualified electrician for service.