Weco Edge 550 - Page 2

221 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Edge 580 - Edge 550

Table of Contents

Default Chapter6
- Table of Contents6
Installation10
Unpacking the Machine12
Removing External Clamps14
Removing the Shipping Rails16
Handling the Covers18
- Removing the Covers18
- Replacing the Covers18
Removing the Internal Clamps20
- Removing the Set Screws20
Preparing the Bench22
- Machine Dimensions22
- Floor Space and Drilling Required23
Water Connections24
- Specifications24
- Pipe Connections24
Electrical Connections28
- Specifications28
- Edger Wiring28
Starting the Edger30
Safety Precautions32
Safety34
- Operator34
- Machine34
Useful Hints36
Utilization38
Presentation40
- Presentation of the Machine40
- Presentation of the Application Screen41
General Principles of Use46
- Usual Procedure46
- Calling up a Job47
- Starting / Interrupting an Edging Cycle48
- Normal Edging Cycle Sequence49
- Important Notes50
  - When Job Data Are Received50
  - During Edging of the Second Lens50
Application Screen Icons52
- General52
- Lens Materials53
- Types of Lenses54
- Finishings55
- Sub-Finishings and Associated Parameters56
  - Groove59
  - Drilling62
- Safety-Bevels63
- Polishing65
- Lens Edging66
Normal Use68
- Producing a Job with Bevel Finishing68
- Producing a Job with Rimless Finishing70
- Producing a Job with Groove Finishing72
- Producing a Job with Drilling Finishing74
- Producing a Job with Grooving and Drilling Finishing76
Special Cases80
- Retouching a Lens80
- Applying an Oversize to the Lens82
- Edging Several Lenses Identically84
- Checking a Finishing before the Lens Is Edged85
Operating Range98
- Points to Remember98
- Illustration of Finishing Limits100
- Drilling102
Configuration104
Presentation of Configuration Menus106
- Presentation of the Configuration Menus Access Screen106
- Presentation of the Personalisation Menus Access107
Configuration of Finishing Default Parameters108
- Presentation108
- Standard Procedure109
- Saving of the New Setting109
- Limits109
Personalisation of Pull-Down Menus112
- Presentation112
- Standard Procedure113
- Saving of the New Personalisation114
- Comments114
  - Button to be Defined114
  - Retouch / Oversizing Menu114
Adjustment of the Setting Values116
- Preliminary Remarks116
- Procedure116
Configuration of General Operating Parameters118
- Presentation118
- Configuration of the Functions119
- Save the New Setting121
Maintenance122
Presentation of Maintenance Menus124
- Presentation of the Maintenance Menus Access Screen124
- Presentation of the Maintenance Screen125
Visualize the Components126
Task List128
Regular Maintenance of the Edger130
- Changing the Swivel Adaptor Blue Pad130
- Changing the Mill Bit132
- Changing the Lens Feeler Tips136
- Dressing a Wheel140
- Cleaning / Replacing the Removable Visor142
- Cleaning Filters and Water Tank144
- Emptying the Water Tank148
- Working in Partial Mode150
Preventive Maintenance152
- Hints152
- Replacement Table for Standard Parts152
Adjustments154
- Presentation of the Settings Menus Access Screen154
- Adjusting Lens Feelers156
- Adjusting Lens Sizes158
- Adjusting the Flush of the Mill Bit164
- Adjusting the Axis with the Alta XL166
- Adjusting the Axis with the Tool170
- Adjusting the Touch Screen172
- Consulting the Setting Values174
Consulting the Statistics176
- Presentation of the Statistics Menu176
- Consultation Principles177
  - Incident Log177
  - The Machine's General Operating Functions177
Messages190
- Types of Messages190
- List of Messages190
Tests200
Presentation of Test Menus202
- Presentation of the Test Menu Access Screen202
- Typical Test Screen203
Operating Principle204
- Operation of the Other Screens205
  - Screen with Switch205
  - Screen with Micro-Switches and Photocells206
Chemistrie208
Chemistrie™ Job Realization212
- Edging of the Sun Lenses213
Technical Specifications214
Characteristics216
Technical Specifications218
- Edge218

Related product manuals

Preview: Weco cad III