3
English
ENG
clothing, gloves, eyewear, and, in certain cases,
protective skin cream are necessary to protect
the skin
►
Follow the coating material and
solvent manufacturer’s warnings and instructions
►
Extraction equipment should be installed by the
user in accordance with local regulations
►
The
objects being sprayed must be earthed
►
Before
each use, check all hoses for cuts, leaks, abrasion
or bulging of cover
►
Check for damage or
movement of couplings
►
Immediately replace the
hose if any of these conditions exist
►
Never repair
a hose
►
Replace it with another grounded high-
pressure hose
►
Pulling the trigger causes a recoil
force to the hand that is holding the airless gun
►
The recoil force of the airless gun is particularly
powerful when the tip has been removed and a
high pressure has been set on the airless high-
pressure pump
►
Therefore, when cleaning without
tip set the pressure control valve to the lowest
pressure
►
Use only manufacturer authorized parts
►
User assumes all risks and liabilities when using
parts that do not meet the minimum specications
and safety devices of the airless gun manufacturer
►
Hazard: Any static-electricity discharge from the
airless gun is to be diverted to the grounded high-
pressure pump via the conductive high-pressure
hose as stipulated
►
The maximum surface
temperature corresponds to the permissible
material temperature
►
This and the permissible
ambient temperature can be found in the technical
data
►
To avoid the generation of machine sparks,
prevent impact stresses and any work on the unit
with tools in the explosion-hazardous area.
RESIDUAL RISKS.
►
Residual risks are risks, which cannot be
excluded, even when equipment is used for the
intended purpose
►
In such cases the applicable
areas of the actual residual risks will be pointed out
using warning and/or prohibition signs.
Risk
Injection
injury
Explosion
or re
Hazaar-
dous
vapors
Can occur
during:
Setup,
operation
Operation
Operation
Impact
Severe
injury or
amputation
Severe
injury
Severe
injury
Source / Cause
Atomized, high
pressure stream
of uid
Static electricity
or sparks
Hazaardous
vapors from spray
material
Preventative
measures
NEVER aim the
gun at any part of
the body
Use well ventilated
area. Ground de
airless gun
Use well ventilated
area. Use mask
WORK AREA SAFETY.
►
Keep work area clean and well lit
►
Cluttered
and dark areas invite accidents
►
Do not handle
airless tools in explosive atmospheres, such as in
the presence of ammable liquids, gases or dusts
►
Keep away from children and curious while
operating a airless tool
►
Distractions can cause
you to lose control.
PERSONAL SAFETY.
►
Stay alert, watch what you are doing and use
common sense when operating a airless tool
►
Do not use a airless tool while tired or under
the inuence of drugs, alcohol or medicines
►
A
moment of inattention while operating airless tools
may cause damage serious personal.
USE PPE’S.
►
Use protection glasses according EN166
►
Use
protection masks according EN149
►
If required by
the type of work, use other precise PPE.
DO NOT WORK ON TIPTOES.
►
Keep your feet on the ground and balance at all
times
►
This enables better control of the airless
tool in unexpected situations.
DRESS PROPERLY.
►
Do not wear loose clothing or jewelry
►
Keep
your hair, clothing and gloves away from moving
parts
►
Loose clothes, jewelry or long hair can be
caught in moving parts
►
If there are devices for
connecting means for extracting and collecting
dust, make sure they are connected and properly
used
►
The use of these devices can reduce dust
related hazards.
STORE AIRLESS TOOLS.
►
Store airless tools out of reach of children and
not allow the handling of airless tools to people
unfamiliar with the tools or these instructions
►
Airless tools are dangerous in the hands of
untrained users.
MAINTENANCE.
►
Check moving parts for misalignment or binding,
there are no broken parts or other conditions
that may aect the operation of airless tools
►
Airless tools are repaired before use when they
To Next Page
Loading...