EasyManua.ls Logo

Wessamat W20 W - User Manual

Default Icon
52 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
W20 W
Betriebsanleitung für WESSAMAT Eiswürfelbereiter
Operating Instructions for WESSAMAT ice cube maker
Mode d´emploi pour WESSAMAT machine à glaçons

Table of Contents

Questions and Answers

  • E
    Elizabeth GonzalezAug 20, 2025
    Why is my Wessamat Ice Maker not working even when switched on?
    • L
      Lori McguireAug 20, 2025
      Your Wessamat ice maker might not be working because: 1. It's not getting power from the socket, so check the socket. 2. The storage container is full and the thermostat has switched off. The ice maker will start again when you remove some ice. 3. The storage container thermostat is switching off too early. Try readjusting or replacing it. 4. The ambient temperature is too low. Try increasing the ambient temperature or moving the device. 5. The production switch is faulty and needs replacing. 6. The production switch is in the wrong position. Push the production switch to the left.
  • K
    Kimberly PatelAug 22, 2025
    What to do if my Wessamat Ice Maker runs but doesn't produce ice?
    • S
      Shannon KlineAug 22, 2025
      If your Wessamat ice maker is running but not making ice, it could be due to: 1. Leaks in the cooling system. Locate and fix any leaks. 2. A faulty compressor. Replace the compressor. 3. A faulty hot gas valve that is stuck open. Replace the hot gas valve.
  • C
    Chelsea SanchezAug 25, 2025
    What causes cloudy ice cubes in my Wessamat Ice Maker?
    • S
      Shaun LarsonAug 25, 2025
      Cloudy ice cubes in your Wessamat ice maker are likely caused by the trough motor not running. Check the trough motor voltage. If voltage is present but the motor isn't turning, replace the trough motor.
  • K
    Kelly MarshAug 26, 2025
    How to prevent ice cubes from sticking together in Wessamat Ice Maker?
    • C
      Cameron WilkinsonAug 27, 2025
      Ice cubes sticking together in your Wessamat ice maker can be caused by: 1. The ice thickness motor switching too late. Readjust the ice thickness motor. 2. Leaks in the cooling system. Locate and fix any leaks, then top up the system.
  • J
    Janice BrownAug 28, 2025
    What to do if Wessamat Ice Maker trough is overfilled with water?
    • S
      suzanne85Aug 28, 2025
      If the trough in your Wessamat ice maker is overfilled with water, it could be due to: 1. The water inlet valve not closing. Replace the water inlet valve. 2. Interrupted probe cables. Measure the electrical conductance of the cables and fix any interruptions, or replace the probe. 3. A fault in the water sensor electronics. Replace the water sensor electronics.
  • L
    Lisa MaxwellAug 30, 2025
    Why Wessamat Ice Maker trough tilts but ice cubes are not discharged?
    • D
      Dr. Kimberly Martinez DDSAug 30, 2025
      If the trough in your Wessamat ice maker tilts fully but doesn't discharge ice cubes, and they stick to the evaporator fingers, it's likely due to a mechanical or electrical fault at the hot gas valve. Replace the hot gas valve.
  • K
    kim09Sep 1, 2025
    How to solve low ice capacity in Wessamat Ice Maker?
    • A
      Anthony WheelerSep 1, 2025
      If your Wessamat ice maker has a low ice capacity, it could be caused by: 1. A dirty condenser. Clean the condenser. 2. The cooling water controller not working properly. Check the cooling water controller, setpoint temperature +30°C, readjust or replace if necessary.
  • J
    Joseph MendezSep 3, 2025
    What causes a Wessamat Ice Maker to produce an ice plate?
    • B
      Brian WilliamsSep 3, 2025
      If your Wessamat ice maker is producing an ice plate instead of cubes, it could be due to: 1. A faulty ice thickness motor. Replace the ice thickness motor. 2. A defective ice thickness limit switch. Replace the ice thickness limit switch. 3. A faulty tilting motor. Replace the tilting motor. 4. The water level being too high. Clean or readjust the water level sensor probe.
  • A
    Angela TorresSep 5, 2025
    What to do if water spills from Wessamat Ice Maker during production?
    • C
      Carolyn Ray MDSep 5, 2025
      If water spills over the edge of the trough during ice cube production in your Wessamat ice maker, it could be because: 1. The machine isn't level. Align the machine. 2. The trough has moved down. Readjust the trough. 3. The water level sensor is dirty. Clean or descale the water level sensor.
  • M
    Michelle SnowSep 7, 2025
    Why won't the trough fill with water in my Wessamat Ice Maker?
    • K
      Kristen FranklinSep 7, 2025
      If the trough in your Wessamat ice maker isn't filling with water, it could be due to: 1. A clogged or dirty water inlet valve. Clean the pre-screen. 2. An electrical fault in the water inlet valve. Check the input voltage and replace the valve if necessary. 3. The water level sensor being affected by moisture. Dry the water level sensor. 4. A fault in the water sensor electronics. Replace the water sensor electronics.

Wessamat W20 W Specifications

General IconGeneral
Daily production20 kg
Cooling systemAir-cooled
RefrigerantR290
TypeIce Maker
Ice typeCube

Related product manuals