Westfield MK130 Plus - User Manual

Questions and Answers

C
Carla BennettAug 14, 2025
Why is my Westfield Tools auger making excessive noise?
- R
  Ricky WhiteAug 14, 2025
  Excessive noise in your Westfield Tools auger could be due to several factors. Initially, remember to follow proper break-in procedures, as the auger may run rough until the tube is polished. If the noise persists, try to determine if it comes from the main or swing-away section by disconnecting the chain from the sprocket drive. Also, inspect for obstructions like cloth or trash wrapped around the flighting, or buildup from oily crops. Check the condition of the flighting at the spout end of the auger; if it has peeled back due to plugging, replacement might be necessary. Make sure that you are using new “E” series cross links and genuine Westfield replacement parts.
G
Gloria CareyAug 17, 2025
What to do if my Westfield Tools auger has excessive PTO angle?
- J
  Jason TurnerAug 17, 2025
  If your Westfield Tools auger has an excessive PTO angle, check the Assembly section for correct dimensions between the auger input and tractor PTO output. Adjust by raising the tractor drawbar to maintain correct dimensions. If extreme side-to-side angles are needed due to bin and tractor placement, consider using a right angle drive kit.
A
Amanda CampbellAug 21, 2025
How to fix bent flighting section on Westfield MK130 Plus?
- A
  Andrew BondAug 21, 2025
  To fix a bent flighting section on your Westfield Tools, support the auger and remove all flight sections. Check the straightness of flight stubs by rolling them across a flat section of concrete floor. Straighten the stub or replace it as needed. Be careful not to bend the flighting when reinstalling.
A
Allison MurphyAug 25, 2025
What to do if Westfield Tools auger has incorrect shear bolt type?
- J
  jacobpearsonAug 25, 2025
  If your Westfield Tools auger has an incorrect shear bolt type, replace it with the correct part number. Westfield shear bolts are specifically designed to provide correct driveline protection.
W
William LeeAug 27, 2025
Why Westfield MK130 Plus Tools auger bearings failing?
- J
  Jacqueline ArcherAug 27, 2025
  If the bearings in your Westfield Tools auger are failing, it could be due to several reasons: * They may not be receiving adequate grease. * The bearing load may not be evenly distributed between the upper and lower bearings. Use the correct sequence of tightening lock collars when setting up or replacing bearings. On MK130 Plus models, adjust the bearing load using the threaded upper flight stub. * Failure of bearing seals. Wet grain or fertilizer will damage seals if left in the boot over time. Clean out the boot before storing the auger.
L
Louis GordonAug 31, 2025
How to fix bent flight stub on Westfield Tools auger?
- J
  Jessica ChapmanAug 31, 2025
  To fix a bent flight stub on the swing flighting of your Westfield Tools auger, remove the flighting and roll it against a flat surface to determine if the stub is true. If it is bent, straighten it or replace it as necessary.
I
idownsSep 3, 2025
What to do if Westfield MK130 Plus auger has high spot at flighting joints?
- G
  gregory52Sep 3, 2025
  If your Westfield Tools auger has a high spot at the flighting joints, check it with a straight edge. If necessary, grind it down until it is even.
A
Alexis MartinezSep 6, 2025
What to do if Westfield MK130 Plus Tools auger has shear bolt hole worn out-of-round?
- S
  Steven GarnerSep 6, 2025
  If the shear bolt hole in your Westfield Tools auger is worn out-of-round, frequent use of an incorrect shear bolt size can wear the mounting hole, creating a "scissor effect," which will require replacement of the affected parts.
K
Kylie MccoySep 10, 2025
What to do if shut off ball valve is open on Westfield MK130 Plus?
- C
  cwestSep 12, 2025
  If the shut off ball valve is open on your Westfield Tools, it indicates that oil is leaking through the tractor valve. The auger ball valve should be closed whenever set up at a bin.