To Next PageTo Next PageWhy can I hear a fan in my Westinghouse Boiler when it's not operating?
The fan may continue to operate after the burner shuts off to clear the exhaust vent of combustion gases, which is normal. Alternatively, the fan might run to help prevent freezing. In this case, protect the appliance from freezing temperatures or shut it off and drain it.
Why does it take long time for Westinghouse WBRCNG140F Boiler to heat water?
If the faucet is located far from the appliance, allow time for the cold water already in the pipes to flow out. You can have recirculation valves and/or plumbing return lines installed and program the unit for recirculation mode.
What to do if Westinghouse WBRCNG140F has no water when faucet is opened?
Check if the water supply valve is shut off at the meter and open it if closed. Also, verify that the water supply valve near the unit is open. If the water pipe is frozen, turn OFF the unit, close all water valves and the gas valve, and contact an authorized service technician. If an error code is flashing on the display panel indicating a leak, contact an authorized service technician.
What to do if Westinghouse WBRCNG140F Boiler water temperature is not hot enough?
Ensure the faucet is open enough to allow at least 0.6 gallons (2.3L) per minute to flow through the appliance. If the outlet water temperature is set too low, adjust it. If an error code is displayed, refer to the Diagnostic and Error Codes section in this manual.
Why is hot water not available from my Westinghouse WBRCNG140F Boiler?
Check if the appliance has power by ensuring it's plugged in and restore power if needed. Then, make sure the unit is turned on by pressing and holding the Power button. Also, ensure the gas supply valve is open. If an error code is flashing on the display panel, refer to the Diagnostic and Error Codes section in this manual.
General| Fuel Type | Natural Gas |
|---|---|
| Input (BTU/h) | 140, 000 |
| BTU Input | 140, 000 BTU/h |
| Gas Connection | 1/2 inch |
| Water Connections | 3/4 inch |
Warnings for operating and installing the boiler.
Discusses issues related to improper combustion.
Information specific to gas fuel.
Guidelines for servicing the boiler.
Information about the boiler system.
Requirements for water chemistry.
Measures for freeze protection.
Adjusting temperature and scald risks.
Considerations for high elevation installations.
Lists components included with the boiler.
Lists optional equipment available.
Guidelines for selecting the boiler's installation location.
Instructions for leveling the boiler.
Required clearances for maintenance.
Specific installation requirements for garages/closets.
Information on exhaust and intake piping.
Requirements for CO detectors.
Preventing contamination of combustion air.
General guidelines for water piping installation.
Information on installing a backflow preventer.
Requirements and installation of an expansion tank.
Instructions for piping the boiler.
Diagrams and explanations of system applications.
General guidelines for venting the appliance.
Lists approved materials for vent and intake piping.
Specific installation requirements for Canada.
Specifies locations for exhaust and intake pipe terminations.
Guidelines for sizing exhaust and intake vent pipes.
Instructions for tightening the boiler collar to vent pipes.
Procedures for installing exhaust and intake vent pipes.
Procedure for removing old appliances from shared venting.
Diagrams and explanations of system applications.
Procedures for venting through an existing system.
Guidelines for power venting with indoor combustion air.
Instructions for electrical wiring connections.
Configuration of DIP switches for boiler operation.
Tables for sizing gas supply pipes.
Requirements for connecting the gas supply.
Precautions for excess flow valves in gas lines.
Procedures for checking gas pressure.
Setting and verifying combustion parameters.
Overview of the control panel and display.
Steps during the boiler's start-up sequence.
How to change the Domestic Hot Water set-point.
How to change temperature units (Fahrenheit/Celsius).
How to change the Central Heating set-point.
Information about the storage mode operation.
How to activate and use the lock function.
How to access and interpret status display information.
Accessing and navigating installer mode settings.
Using the outdoor sensor for temperature control.
Connecting and using a 0-10 Volt input signal.
Explains error codes and their meanings.
Flowcharts for diagnosing error codes.
Common problems and their solutions.
Procedures for checking and controlling water chemistry.
How to check for gas leaks.
Instructions for using freeze protection fluids.
Steps for filling and testing the water system.
Procedures for purging air from the system.
Steps for purging air from the DHW system.
Checking thermostat wiring and circuits.
Information on condensate removal systems.
Steps for starting up, adjusting, and testing the boiler.
Warranty details for residential use.
Warranty details for commercial use.
List of conditions not covered by the warranty.
