To Next PageTo Next Page
Need help?Do you have a question about the Wharfedale Pro Diamond 9.1 and is the answer not in the manual?
General| Configuration | 2-way |
|---|---|
| Type | Bookshelf |
| Frequency Response | 50Hz - 24kHz |
| Sensitivity | 86dB |
| Impedance | 6 Ohms |
| Nominal Impedance | 6 Ohms |
| Recommended Amplifier Power | 20-100W |
| Bass Driver | 130mm woven Kevlar cone |
| Woofer | 130mm woven Kevlar cone |
| Tweeter | 25mm textile dome |
Checklist for diagnosing and resolving system issues before returning a unit to the dealer.
Instructions for cleaning and maintaining the loudspeaker cabinets and drive units.
Details on returning units for repair, guarantee exclusions, and service center contact.
List of authorized service locations in the UK, USA, and Canada.
Statement of product compliance with relevant EU and FCC standards.
Guidance on positioning and configuring two subwoofers for optimal bass response.
Initial steps for unpacking speakers and preparing them for use.
Explanation of the crossover panel, terminal connections, and metal straps.
Instructions for attaching plinths and spikes to the loudspeakers for stability.
Advice on selecting appropriate audio cables and preparing them for connection.
Details on using the remote handset, installing batteries, and powering on the unit.
Guidance on subwoofer placement, listening rooms, and home cinema environment setup.
Specific advice for positioning front, centre, and surround loudspeakers.
Setup, fitting feet, rear panel connections, and subwoofer connection for the SW 250.
Rear panel connections and subwoofer connection for the SW 150 model.
Details on connecting to A/V processors, stereo line outputs, and pre/main amplifiers.
Explanation of the control panel functions including volume, filters, and presets.
Instructions for connecting the subwoofer using high-level speaker connections.
Guide for connecting the subwoofer to an A/V processor's line level or LFE output.
Methods for connecting the subwoofer using stereo line level outputs.
Detailed methods for connecting via pre-amplifier outputs and main amplifier inputs.
Guidelines for setting up front, centre, and surround speakers in a home cinema system.
Advice on configuring speaker sizes ('Large'/'Small') in AV processors.
Instructions for setting channel levels, delay settings, and subwoofer output.
Guidance on setting the LFE channel, stereo reproduction, and low pass filter adjustments.
Tips for low-level listening, system testing by ear, and using an SPL meter.
Diagrams and instructions for standard and bi-wired connections to front speakers.
Connection methods for centre and surround speakers, including bi-wiring.
Recommendations for optimal placement of stereo loudspeakers.
Adjusting subwoofer blend, phasing, and levels for optimal sound.
Essential safety precautions for operating the Diamond 9 Series loudspeakers.
Advice on signal input, amplifier volume, and avoiding picture distortion.
Details regarding mains plug fuses and wire colour coding for UK users.
Technical specifications for Diamond 9 bookshelf models (9.0, 9.1, 9.2, 9.3).
Technical specifications for Diamond 9 floorstanding models (9.4, 9.5, 9.6).
Technical specifications for Diamond 9 centre and surround models (9.CC, 9.CS, 9.CM, 9.SR, 9.DFS).
Diagram showing the layout of rear panel terminals for subwoofer connectivity.
Detailed instructions for connecting the subwoofer to various audio sources.
Identification and explanation of the subwoofer's front panel controls.
Methods for connecting the subwoofer to amplifiers using RCA or speaker level inputs.
Instructions for connecting the subwoofer via high-level speaker terminals.
Two alternative methods for connecting the subwoofer within an amplifier loop.
Guidance on positioning front and surround speakers for optimal home cinema experience.
Instructions for adjusting channel levels to achieve balanced loudness.
Advice on setting the LFE level to avoid overloading the subwoofer.
Adjusting volume, phase, and low pass filter for optimal bass performance.
Setting speaker sizes, levels, delay, and LFE for home cinema systems.
Adjusting the low pass filter for stereo playback based on main speaker size.
Considerations for listening at low volumes while retaining bass information.
Methods for testing system performance and identifying setup issues.
Detailed technical specifications for Diamond 9 bookshelf models.
Detailed technical specifications for Diamond 9 floorstanding models.
Detailed technical specifications for Diamond 9 centre and surround models.
