Why does my Whirlpool 4322525 Ranges door lock but indicator lights do not light?
If the door on your Whirlpool Ranges locks but the indicator lights don't light and the oven doesn't begin the clean cycle, the indicator light may be defective and need replacement. Also, the latch safety switch could be defective and require replacement.
What causes a chipped oven liner on a Whirlpool 4322525 Ranges?
A chipped oven liner in your Whirlpool Ranges could be due to damage during shipping. You can repair or replace the liner. To repair smooth porcelain bronzetone, order P/N 242756.
What to do if Whirlpool Ranges oven cooks but display does not count down?
If your Whirlpool Ranges oven cooks, but the display doesn't count down during the cooking cycle, there may be loose or bad wiring to the harness, which needs repair or replacement. Alternatively, the microcomputer board may have failed and needs replacement.
Why is the door sagging on one side on my Whirlpool 4322525?
If the door on your Whirlpool Ranges is sagging on one side, the hinge may be loose or out of position relative to the oven liner. Adjust the hinges to correct this.
Why does my Whirlpool 4322525 Ranges clock display not show 4 number eights after power-on?
If the clock display on your Whirlpool Ranges doesn't show four number eights after the power-on test, there may be loose or bad wiring, which needs repair or replacement. The clock display may not be properly seated, or there could be a burned-out or missing segment in the display. In some cases, there might be a broken or missing terminal on the microcomputer, requiring replacement of the microcomputer board.
What causes a damaged oven door gasket on a Whirlpool Ranges?
A damaged oven door gasket on your Whirlpool Ranges can result from improper cleaning. Avoid using harsh abrasives or scouring pads. Refer to the Use & Care instructions for proper cleaning methods.
What to do if Whirlpool Ranges electronic timer will not accept programming?
If the electronic timer on your Whirlpool Ranges won't accept programming, the electronic board has likely failed and needs replacement.
Why is the oven door on my Whirlpool Ranges difficult to open?
If the oven door on your Whirlpool Ranges is difficult to open, the broil stop rollers may be worn or broken and need replacement.
Why does the bake element in my Whirlpool Ranges burn out prematurely?
Premature burnout of the bake element in your Whirlpool Ranges can be caused by improper oven use, such as using it to heat the home. Use the oven for baking only.
What to do if the Whirlpool 4322525 oven element does not heat?
If the oven element in your Whirlpool Ranges isn't heating, first check the circuit breaker. If that's fine, there may be loose or bad wiring, which needs repair or replacement. The element itself could also be defective and might need testing or replacement.
Details the necessary electrical supply, wiring, and grounding for proper appliance installation.
Explains the types of power supply cords required and their specifications for connection.
Instructions for testing the cooling fan motor windings for continuity and resistance.
Procedure to test the continuity of element controls under different settings.
Instructions for testing surface elements for resistance using an ohmmeter.
Instructions for testing the oven temperature sensor resistance at various temperatures.
Lists common error codes, their likely failure conditions, and troubleshooting steps for oven circuits.
Detailed wiring diagram illustrating the electrical connections between all components of the appliance.
Shows simplified circuit diagrams for specific functions like cleaning, oven light, and quick disconnect plugs.
Simplified circuit diagrams illustrating the electrical paths for bake and broil functions.
Circuit diagrams for ceramic and coil cooktop surface units, showing element and limiter connections.
Details the necessary electrical supply, wiring, and grounding for proper appliance installation.
Explains the types of power supply cords required and their specifications for connection.
Instructions for testing the cooling fan motor windings for continuity and resistance.
Procedure to test the continuity of element controls under different settings.
Instructions for testing surface elements for resistance using an ohmmeter.
Instructions for testing the oven temperature sensor resistance at various temperatures.
Lists common error codes, their likely failure conditions, and troubleshooting steps for oven circuits.
Detailed wiring diagram illustrating the electrical connections between all components of the appliance.
Shows simplified circuit diagrams for specific functions like cleaning, oven light, and quick disconnect plugs.
Simplified circuit diagrams illustrating the electrical paths for bake and broil functions.
Circuit diagrams for ceramic and coil cooktop surface units, showing element and limiter connections.
To Next Page
General