EasyManua.ls Logo

Whirlpool ADG 8210 - User Manual

Whirlpool ADG 8210
8 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
GB
-1-
Chart
(see at right for options description)
PROGRAMME SELECTION BUTTON
Press button “P” (repeatedly) until the
required programme number appears on
the display (see “Table of programmes”
below).
START BUTTON
The indicator lights up during operation,
flashes when a fault occurs and goes off at
the end of the programme.
ON
BUTTON
OFF
BUTTON
FAULT INDICATION AND WASH TIME DISPLAY
In normal operation it indicates the remaining time (h:mm), whereas with
“Delayed start” selected it indicates the time remaining until programme
start (hh).
If “F..” appears on the display, see chapter “What to do if...”.
RESET BUTTON
For programme change or indication of faults.
Press this button to cancel a started programme and selected extra
options. Press this button to cancel the main fault indicators “F..”
also refer to the chapter “What to do if...”. The programme can then
be selected and started.
1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance’s automatic calibration system.
2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Table of programmes
Deter-
gent
Consumption
P
Programmes
Available
options
Loading instructions
Litres Kwh
Minutes
1)
1
Aqua Steam 40-70°C
Delay
Multizone
Power Clean
Normally or heavily soiled crockery,
including pots and pans. Thanks to steam
action, soaking or hand pretreatment is no
longer needed. In addition hygiene is
ensured due to the high temperature
steam.
X 7-15 0.99-1.75 65-205
2
Pre-Wash cold
Delay
Multizone
Crockery to be washed later. 4.0 0.03 14
3
Glasses 40°C
Delay
Multizone
Light soiling, for example glasses and
cups.
X 10.0 0.85 100
4
Quickwash 45°C
Delay
Multizone
Lightly soiled crockery, with no dried-on
food.
* Not recommended tablets use.
X
*
11.0 0.80 30
5
Bio
2)
50°C
Delay
Multizone
Power Clean
Normally soiled crockery.
Energy-saving programme.
X 10.0 1.05 145
6
Antibacterial
3)
Delay
Multizone
Power Clean
Normally or heavily soiled crockery,
with additional antibacterial wash.
Programme interruption (e.g. due to
door opening) can compromise
elimination of germs.
X 13.0 1.50 115
7
Overnight 55°C
Delay
Multizone
Normally soiled crockery, gentle and
quiet thanks to the lower spray pressure
(39dbA).
X 13.0 1.20 290
5019 396 01784ADG 8210
Options and display description
BEFORE USING THE APPLIANCE FOR THE
FIRST TIME CAREFULLY READ THIS QUICK
REFERENCE GUIDE AND THE ASSEMBLY
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.
HALF LOAD/
MULTIZONE
Allows you to choose
the washing zones.
Press this button
(repeatedly) to select
the wash zones:
both racks
only upper
rack
only lower
rack
POWER CLEAN
Thanks to the
additional power jets
this option provides a
more intensive and
powerful wash in the
lower rack, in the
specific area. This
option is
recommended for
washing pots and
casseroles
(see
page 4)
. Press this
button to activate
Power Clean (the
indicator lights up).
RINSE AID
INDICATOR
When lit, the rinse aid
dispenser needs to be
refilled.
SALT INDICATOR
When lit, the salt
reservoir needs to be
refilled.
SET THE
DETERGENT
Press this button
(repeatedly) to set the
type of detergent used.
Powder, gel
(standard)
Detergent
with rinse aid
Detergent
with salt +
rinse aid
DELAYED START
BUTTON
Press the button
(repeatedly) to delay
the start of the
programme.
Adjustable from 1 to 24
hours. With each press
of the button, the
delayed start indicator
increases by one hour
and after 24 resets
from 00. Then press
the START button. The
dishwasher will start
after the set time.
Quick reference guide

Questions and Answers

  • A
    Alicia DorseySep 9, 2025
    Why aren't glasses sparkling after using my Whirlpool Dishwasher?
    • C
      Carol RuizSep 9, 2025
      If glasses are not sparkling after using your Whirlpool Dishwasher, it could be because the glasses are not suitable for dishwasher use. Some types of glass cannot be washed in the dishwasher.
  • S
    Sarah LeeAug 22, 2025
    Why are my dishes not dry after Whirlpool ADG 8210 Dishwasher cycle?
    • J
      Janice MurphyAug 23, 2025
      If your dishes are not dry after a cycle in your Whirlpool Dishwasher, it could be due to several factors. Plastic containers don't dry well, so wipe them manually if needed. If you leave clean dishes in the dishwasher for a long time after the cycle, it's normal to find some water droplets; try opening the door 5 minutes before unloading. Ensure concave items are arranged so water doesn't collect in them. Also, check that you're using the correct dosage of rinse aid. If you selected a rapid program, remember it's for lightly soiled dishes; for a full load, select a standard program and open the door 15 minutes after the cycle ends.
  • S
    Shelby BrowningAug 25, 2025
    What to do if my Whirlpool ADG 8210 Dishwasher shows F4?
    • D
      Donna CainAug 25, 2025
      If your Whirlpool Dishwasher displays “F4” or the start indicator lamp flashes 4 times, it indicates a drainage issue. You should clean the filters, ensure that the drain hose is not kinked, and verify that the closure disk of the syphon hose connection has been removed.
  • G
    gtaylorAug 27, 2025
    What to do if my Whirlpool ADG 8210 Dishwasher shows F6?
    • M
      Marcus BlackAug 27, 2025
      If your Whirlpool Dishwasher shows “F6” or the start indicator lamp flashes 6 times, it means there's a water inlet problem. Make sure the water tap is fully open. Also, check that the water inlet hose isn't kinked and the inlet filter in the water tap connector isn't clogged.
  • C
    Christopher DavisAug 27, 2025
    What to do if my Whirlpool ADG 8210 shows F7?
    • A
      Allen MitchellAug 27, 2025
      If your Whirlpool Dishwasher displays “F7” or the start indicator lamp flashes 7 times, it indicates low water pressure. Ensure the water tap is fully open during water inlet, providing a minimum capacity of 0.5 liters per minute. Also, check that the water inlet hose isn't kinked and the inlet filter in the water tap connector isn't dirty.
  • J
    johnsonalyssaAug 29, 2025
    How to fix dirty dishes in my Whirlpool ADG 8210 Dishwasher?
    • W
      williamskendraAug 29, 2025
      If your crockery and cutlery are not perfectly clean after a wash cycle in your Whirlpool Dishwasher, consider these points: * Ensure there is enough space between the dishes, arranging them so they don't touch. Place concave items facing downwards. * Use enough detergent, making sure it's not too old or incorrectly stored. * Select a wash program with a higher temperature for heavily soiled items. * If using the “Half load/Multizone” option, load only the upper or lower rack. * If you frequently use the Eco 50°C program, occasionally use the Intensive 70°C program. * Check that the spray arms are not clogged, and the filters are clean and correctly fitted. * Make sure the spray arms can turn freely and are not blocked by crockery or cutlery.
  • D
    Daniel FischerSep 17, 2025
    Why do plastic parts in my Whirlpool ADG 8210 have discoloured?
    • V
      Victor WebsterSep 18, 2025
      Discoloration of plastic parts in your Whirlpool Dishwasher can be caused by tomato or carrot juice. Using powder detergent is recommended, as it allows for slightly higher doses for improved whitening. Also, use programs with higher wash temperatures.
  • T
    Tracy RobinsonSep 18, 2025
    Why do tea cups darken in my Whirlpool ADG 8210 Dishwasher?
    • S
      Samantha RiggsSep 19, 2025
      Darkening of tea cups in your Whirlpool Dishwasher is inevitable, as theine alters the colors permanently.
  • A
    Alexandra ChenSep 7, 2025
    Why are there removable deposits on glasses from my Whirlpool Dishwasher?
    • D
      Daniel MillerSep 8, 2025
      Removable deposits on glasses from your Whirlpool Dishwasher can occur if you're using incorrect programs for glasses. Ensure dishes are arranged to avoid touching each other, and glassware is not placed together in baskets. Use a suitable program specifically for glass.
  • D
    Don NunezSep 4, 2025
    Why are there streaks on dishes from my Whirlpool Dishwasher?
    • S
      Stephen RogersSep 4, 2025
      If your Whirlpool Dishwasher leaves streaks on dishes, the rinse aid dosage might be too high. Reduce the rinse aid dosage. If you are using a combined action detergent that includes rinse aid, do not add any additional rinse aid.

Summary

Fault Indication and Wash Time Display

Options and Display Description

How to Set Water Hardness

Filling the Salt Reservoir

Adding Rinse Aid

Adding Detergent

Loading the Upper Rack

Loading the Lower Rack

Using the Power Clean Feature

Maintenance and Fault Rectification

Filters

Procedures for checking and cleaning filters.

Troubleshooting: Appliance Not Working

Troubleshooting: Crockery Not Clean

Troubleshooting: Crockery and Cutlery Issues

Disconnecting the Mains Plug

Precautions and General Recommendations

Child Safety

Important safety measures concerning children.

Safety Warnings

General safety guidelines for appliance operation.

Whirlpool ADG 8210 Specifications

General IconGeneral
ColourWhite
Energy efficiency classA
Washing classA
Drying classA
Number of place settings12
Number of washing programs6
Noise level52 dB
Place Settings12
Delay StartYes
Weight42 kg

Related product manuals