Why won't my Whirlpool ADG 271 Dishwasher start?
Your Whirlpool Dishwasher might not start because the water supply tap is not turned on, the dishwasher door has not been closed properly, the appliance has not been plugged in properly, or the appliance needs to be switched off and back on to reset the wash cycle.
What to do if my Whirlpool ADG 271 Dishwasher is not draining water?
If your Whirlpool Dishwasher isn't draining water, it could be due to several reasons: * The wash cycle hasn't finished yet. * The water drain hose is bent. * The drain duct is clogged up. * The filter is clogged up with food residues. * The height of the drain hose.
Why are my dishes not clean after Whirlpool Dishwasher cycle?
If your dishes aren't clean after a Whirlpool Dishwasher cycle, consider these possibilities: * The crockery hasn't been arranged properly. * The spray arms can't rotate freely. * The wash cycle is too gentle. * There's too much foam due to incorrect detergent usage. * The lid on the rinse aid compartment isn't closed correctly. * The filter is dirty or clogged. * The refined salt level is low. * The height of the dishes isn't compatible with the rack adjustment. * The holes in the spray arms are clogged up.
Why aren't my dishes drying in my Whirlpool Dishwasher?
If your crockery has not been dried properly in your Whirlpool Dishwasher, it might be because a wash cycle without a drying programme has been selected, the rinse aid has been used up, the rinse aid dispenser setting is not suitable, or the crockery is made from non-stick material or plastic.
How to fix Whirlpool ADG 271 that won't load water and has flashing lights?
If your Whirlpool Dishwasher won’t load water and has flashing lights, check the following: 1. Ensure there is water in the mains supply and the tap is open. 2. Make sure the water inlet hose isn't bent. 3. Clean any clogged filters. 4. Clean the clogged drain duct. After checking and cleaning, switch the dishwasher on and off and start a new wash cycle. If the problem persists, turn off the water tap, remove the plug and call the Service Centre.
How to reduce noise from a Whirlpool ADG 271 Dishwasher?
To reduce excessive noise from your Whirlpool Dishwasher: * Ensure dishes aren't rattling against each other or the spray arms; place them properly and make sure the spray arms can rotate freely. * Avoid too much foam by measuring detergent correctly and using a suitable dishwasher detergent. Do not prewash the dishes by hand.
Why is there white film on dishes from Whirlpool ADG 271?
If your dishes and glasses are covered in a white film or limescale deposits after using your Whirlpool Dishwasher, it could be due to: * Lack of refined salt. * Unsuitable water hardness adjustment. * The salt and rinse-aid dispenser cap not being closed properly. * The rinse aid being used up or the dosage being too low.
Why won't the door close on my Whirlpool ADG 271?
If the door on your Whirlpool Dishwasher won’t close, make sure that the racks were inserted all the way and that the lock was released. Strongly push the door until a “clacking” noise is heard.
Why are my dishes streaked after using my Whirlpool ADG 271 Dishwasher?
If the dishes and glasses are streaked or have a bluish tinge after using your Whirlpool Dishwasher, it may be because the rinse aid dosage is too high.
Covers water supply connection, hoses, and flood protection system.
Instructions for electrical connection of the appliance.
Guidance on how to position and level the appliance.
Recommendations for the first wash cycle.
How to set the water hardness level.
Diagram and identification of appliance parts.
Explanation of the control panel layout and functions.
Instructions for filling the salt dispenser.
How to adjust the water softener based on hardness.
Instructions for filling the rinse aid dispenser.
How to adjust the rinse aid dosage for drying.
Proper placement of cutlery in the basket.
Guidance for loading items into the lower rack.
Guidance for loading items into the upper rack.
How to adjust compartments for optimal loading.
How to measure and use detergent correctly.
Step-by-step guide to starting a wash cycle.
How to change a wash cycle after it has started.
Instructions for adding more dishes during a cycle.
What happens during power cuts or door opening.
How to use the tablet option for optimal results.
Instructions for using the half load option to save resources.
How to set a delayed start for the wash cycle.
How to safely disconnect water and power supplies.
Guide to cleaning the exterior and interior of the dishwasher.
Tips to avoid and prevent bad smells in the appliance.
Instructions for cleaning the spray arms.
Guide to cleaning the dishwasher filters for optimal performance.
How to clean the water inlet filter.
Instructions for safely storing the appliance when not in use.
General| Door color | Not applicable |
|---|---|
| Cord length | 1.3 m |
| Control type | Buttons, Touch |
| Product size | Full size (60 cm) |
| Built-in display | No |
| Inlet hose length | 1.5 m |
| Appliance placement | Fully built-in |
| Control panel color | Black |
| Upper basket adjustable height | Yes |
| Current | 13 A |
| Connected load | 1900 W |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 Hz |
| Power consumption (off) | 0.5 W |
| Water consumption per cycle | 10 L |
| Energy consumption per cycle | 0.83 kWh |
| Drying class | A |
| Annual water consumption | 2800 L |
| Annual energy consumption | 237 kWh |
| Cycle time | 180 min |
| Noise level | 49 dB |
| Delay start (max) | 12 h |
| Dishwashing programs | - |
| Number of place settings | 10 place settings |
| Number of washing programs | 6 |
| Package depth | 675 mm |
| Package width | 500 mm |
| Package height | 910 mm |
| Package weight | 33500 g |
Weight and Dimensions| Depth | 555 mm |
|---|---|
| Width | 448 mm |
| Height | 900 mm |
| Weight | 31500 g |
| Installation compartment depth | 570 mm |
| Installation compartment width | 450 mm |
| Installation compartment height | 820 mm |
To Next Page