Why does my Whirlpool AWO/C 7420 S Washer vibrate during the spin cycle?
Your Whirlpool Washer may vibrate during the spin cycle if the transport bolts haven't been removed. Make sure to remove them before using the appliance. Also, check that the appliance is level and standing firmly on all four feet. Refer to the Installation Guide for details.
What to do if my Whirlpool AWO/C 7420 S stops during the program?
If your Whirlpool Washer stops mid-cycle and the Start/Pause light is blinking, here are a few things to check: * If 'Rinse hold' is activated, press 'Start(Pause)' to spin the laundry. To drain water without spinning, select the 'Drain' program or press the 'Reset/Drain' button for 3 seconds. * If the program was changed, reselect your desired program and press 'Start(Pause)'. * If the door was opened, close it and restart the program with 'Start(Pause)'. * The appliance’s safety system may have been activated. * Ensure the water tap is open and the inlet hose isn't kinked or blocked.
How to fix Whirlpool Washer unbalance during spinning?
If your Whirlpool Washer experiences unbalance during spinning, it's likely due to an unbalanced laundry load. To resolve this: * Avoid washing small laundry loads. * Add other laundry items of different sizes when washing a big or heavy piece of laundry. If you want to spin the wet laundry, add more laundry items of different sizes, and subsequently select and start the “Rinse & Spin” programme.
What to do if my Whirlpool AWO/C 7420 S Washer doesn't start?
If your Whirlpool Washer doesn't start even after pressing 'Start/Pause', check these: * Ensure the door is properly closed. * If available, the “Child lock/Lock buttons” feature might be activated. To unlock, press and hold the two buttons marked with the key symbol simultaneously for at least 3 seconds, until the key symbol disappears from the display.
Why my Whirlpool AWO/C 7420 S final spin results are poor?
Poor final spin results in your Whirlpool Washer can occur due to: * Unbalance during spinning prevented spin phase to protect the washing machine. * Excessive foam formation prevented spinning; select and start “Rinse & Spin” programme. Avoid excessive detergent dosing. * The “Spin” button has been set to a low spin speed.
What to do if my Whirlpool AWO/C 7420 S does not start and no indicators are on?
If your Whirlpool Washer isn't starting and no indicators are lit, check if the plug is properly inserted in the socket. Also, test the socket or fuse with a table lamp or similar appliance to ensure they're functioning correctly.
Why are there detergent residues on laundry after wash in my Whirlpool AWO/C 7420 S Washer?
Detergent residues on laundry after washing in your Whirlpool Washer may be due to insoluble compounds used in phosphate-free powder detergents. To address this: * Avoid overdosing detergent. * Use liquid detergent. * Select the “Intensive Rinse” option, if available. * Brush out the fabric.
Why does my Whirlpool AWO/C 7420 S have detergent residues in the dispenser?
If you notice detergent residues in the dispenser of your Whirlpool Washer, it could be due to insufficient water entering. The mesh filters of the water supply might be blocked. Please refer to the “Care And Maintenance” section for instructions on how to clean them.
Why is my Whirlpool AWO/C 7420 S Washer at a standstill in the middle of a program?
If your Whirlpool Washer pauses for several minutes mid-cycle, it could be due to too much detergent. If the foam persists, the red “Service” indicator will light up and the display shows “F18” or “Fod” - refer to the instructions concerning the “Service” indication on the next pages in this case.
What to do if my Whirlpool AWO/C 7420 S shows 'Clean pump'?
If your Whirlpool Washer displays 'Clean pump', it means waste water is not being pumped out. Unplug the appliance and check for: * Kinks or blockages in the drain hose. * A blocked filter or pump. Ensure the water has cooled before draining the appliance; see the chapter (“Draining Residual Water/Cleaning The Filter”). * A frozen drain hose. After resolving the issue, push the “Reset” button for at least 3 seconds, then restart the desired program.
Essential safety precautions for using the washing machine safely.
Guidance on placing and levelling the washing machine.
How to connect the water supply hose correctly.
Instructions for connecting the drain hose.
Safety and procedural requirements for electrical hook-up.
Meanings of error codes and indicator lights.
How to adjust the machine's feet for stability.
Connecting the water supply hose to the tap and machine.
Ensuring a safe and compliant electrical connection.
To Next Page
General